Tire Size Fitment Master Thread

[Travis9935]

that is perfect thank you! Was planning on getting the tremor fender flares and wanted to make sure that same wheel/tire size will sit about even and i think they do! Looks like about a 1” poke if im not mistaken.

If that even

Sponsored

 

[Michael Bailey]

I am seeking a set of 18" Hankook takeoffs in New Mexico.

Anybody have a set taking up space in your garage?

 

[Volkswilliam]

Looking for larger tires for my 2019 FX4 w/ 2.5" level kit. Stock sport wheels.

Looking at the Grabber ATX 275/70/17 which is similar to 265/70/18 which I've read works great. Can anyone confirm?

 

[CFLRANGER]

Please help! Can't draw any definite conclusions after reading all the threads. Will I have rubbing issues if I'm looking at 2.5in level with 17x8.5 +10 wheels with 265/70r17 tires. Thanks in advance for any input.

 

[YaBoiNewton]

Please help! Can't draw any definite conclusions after reading all the threads. Will I have rubbing issues if I'm looking at 2.5in level with 17x8.5 +10 wheels with 265/70r17 tires. Thanks in advance for any input.

That size will likely fit just fine. Best thing to do is try it out and adjust as needed once the tires are on.

 

[Regnar]

Just installed new wheels and tires to go with my new lift.

Motegi Trailite 17x8.5 +18 offset
285/70/17 Cooper Discoverer At3 XLT Load Range E
Old man emu standard lift
Readylift intrusion bars


Tasteful poke, no rub.

 

[kcederwall08]

Finally got my wheel/tire and suspension set up
Wheels: Relations Race Wheels RR6-H, 17x8.5 0 offset in matte bronze
Tires: BFG k02, 285/70/17
Suspension: Fox 2.5 front and rear, front raised about 2.5"
Cut out rear intrusion beams, they were rubbing, cut out some fender liner that rubbed behind the tire, and BDS front intrusion beam. Fog light pockets removed to add dual light bracket.

Still some rubbing on the fender liner, I need to cut a bit more out, but doesn't seem to rub on any chassis parts!

 

[Bob902]

Finally got my wheel/tire and suspension set up
Wheels: Relations Race Wheels RR6-H, 17x8.5 0 offset in matte bronze
Tires: BFG k02, 285/70/17
Suspension: Fox 2.5 front and rear, front raised about 2.5"
Cut out rear intrusion beams, they were rubbing, cut out some fender liner that rubbed behind the tire, and BDS front intrusion beam. Fog light pockets removed to add dual light bracket.

Still some rubbing on the fender liner, I need to cut a bit more out, but doesn't seem to rub on any chassis parts!

I see two trucks and three trash dumpsters

 

[Venom_z89]

Finally got my wheel/tire and suspension set up
Wheels: Relations Race Wheels RR6-H, 17x8.5 0 offset in matte bronze
Tires: BFG k02, 285/70/17
Suspension: Fox 2.5 front and rear, front raised about 2.5"
Cut out rear intrusion beams, they were rubbing, cut out some fender liner that rubbed behind the tire, and BDS front intrusion beam. Fog light pockets removed to add dual light bracket.

Still some rubbing on the fender liner, I need to cut a bit more out, but doesn't seem to rub on any chassis parts!

Damn looks good

 

[Utah_Bound]

I am trying to decide between a +35 and a +20. Both are 17x8. My tire choice is a 33x10.5R17. I will be using the ReadyLift bars with a OME standard lift. Any input would be helpful for an ideal fitment. I've used the tire size calculator and the backspace calculator to get an idea of where it will sit, but I still can't imagine it in my head. I don't want too much poke, but I am ok with some, if that makes sense. Thanks! I havn't found anyone one with this exact setup. I have seen several +18 offests that look good though.

 

[Utah_Bound]

Just installed new wheels and tires to go with my new lift.

Motegi Trailite 17x8.5 +18 offset
285/70/17 Cooper Discoverer At3 XLT Load Range E
Old man emu standard lift
Readylift intrusion bars


Tasteful poke, no rub.

How are you liking the standard OME lift? Your build is very similar to what I am trying to achieve! I want to go with 17x8 +20 with 33x10.5R17 tires. Except for crash bars, are you close to rubbing anywhere, even at full articulation? Thanks!

 

[Regnar]

How are you liking the standard OME lift? Your build is very similar to what I am trying to achieve! I want to go with 17x8 +20 with 33x10.5R17 tires. Except for crash bars, are you close to rubbing anywhere, even at full articulation? Thanks!

I'm loving the setup so far - the wider tires feel a lot more planted, and the suspension is more firm but not harsh at all - just more planted. Totally with the money invested. As far as rubbing goes, I did trim the black aero thing that deflects air from in front of the front tires. Other than that, nothing. I would personally go with the 20mm offset in your situation - you'll still have tasteful poke, but it'll be just a bit less poke than my setup.
Here's some more pics to get an idea of my current poke-age:

 

[ICE 27]

Anyone fit a 275/70/18 rugged trek 33.6 with a 2.5 lift?

 

[amick1995]

I’ve been searching for a couple hours now, but can’t seem to find any solid answers. When the time comes I’m looking to upgrade my tremor tires to a 285/75/r17. I’ve got a 2 inch level and will either run spacers or get new wheels.

anyone know if the 285/75/r17 will fit in the factory spare tire location? I know a 285/70/r17 will.
Thanks!

 

[Venom_z89]

I’ve been searching for a couple hours now, but can’t seem to find any solid answers. When the time comes I’m looking to upgrade my tremor tires to a 285/75/r17. I’ve got a 2 inch level and will either run spacers or get new wheels.

anyone know if the 285/75/r17 will fit in the factory spare tire location? I know a 285/70/r17 will.
Thanks!

It will. It's tight but it fits

Sponsored