GregsFX2Ranger
Well-Known Member
Why is it that Ford dealers(service departments) refuse to look at Blackstone analyses?
Sponsored
I have a feeling that the dealerships don’t know what to do to resolve the issue. Some have replaced the injectors but has it actually fixed the problem? My conspiracy theory is that the frequent priming of the engine is somehow involved. I have had 4 modern turbo charged engines and several have been GDI. I have a 3.5 EB in my driveway that never audibly primes the fuel pump. I have heard my ranger prime many times when it’s just sitting there. Also, does it truly need to prime every time you open the door or is that some engineers bright idea that isn’t really necessary? Makes you wonder since other Fords don’t have the reported priming behaviors that the ranger have. Additionally my understanding is that fuel dilution isn’t as prevalent on any of the other 2.3 applications so what is different. I am thinking it’s software and Ford is basically ignoring it or doing something quietly that we will hear about later.Why is it that Ford dealers(service departments) refuse to look at Blackstone analyses?
Firstly: i would also want to disable that priming, but am not sure if there's a problem turning it off.Also, does it truly need to prime every time you open the door or is that some engineers bright idea that isn’t really necessary?
Thanks for posting, Bob. That was an interesting read. They also said this:Interesting take at https://polarislabs.com/how-gasoline-engine-technology-affects-fuel-dilution/. I highlighted the part that seems to go against the idea that using higher viscosity oil helps mitigate dilution damage. Seems counterintuitive, and likely to be poo poo'd by some.
How much is acceptable?
While OEMs do not publish acceptable numbers, the common range used by most is that 3 - 7% can be acceptable as long as there is not a noticeable increase in wear or drop in lubricant viscosity. Most OEMs are using low viscosity oils that tend to be more tolerant of higher amounts of fuel.
Our laboratory will report fuel dilution by two methods. The first method will be an estimate based on the viscosity result. If the viscosity has not dropped further than one centistoke from the midpoint of the SAE grade identified for the sample, an estimate of <1% fuel will be reported. However, if the viscosity has dropped further than one centistoke, the sample is then tested for fuel dilution using Gas Chromatography (GC) method ASTM D7593 for an exact percentage of fuel. The unleaded gasoline fuel dilution method by GC is calibrated up to 5%. If the GC registers a result higher than 5%, a result of >5% will be reported. Exact percentages above 5% cannot be reported due to the calibration limits.
I will be patiently waiting to hear Jim's next test results with the 5W40.What do you need to watch?
Higher percentages of fuel dilution are not ideal as fuel does not have the same lubricating properties of oil and can lead to early wear. Monitoring wear metals becomes paramount to determining if the oil is maintaining the proper lubricant film. You will also want to monitor the lubricant viscosity as well as the other lubricant properties such as base number, oxidation and nitration. If the wear metals are increasing and the viscosity is decreasing, reducing the interval time or increasing the viscosity of the oil may be recommended.
When my XLT was stock you could definitely hear it priming randomly. After I put on the collector engine cover it’s barely noticeable now. Now my hearing isn’t all that great anymore so your mileage may varyHas anyone confirmed that the sounds from the truck when off is actually the fuel pump priming?
That is what my level looks like, slightly over. Luckily, I haven't smelled gas in the oil.. I have about 350 miles so far.Well posting in this thread reminded me to go check my oil. It absolutely reeks like fuel. You can smell it as soon as I pull the dipstick it stinks up the garage. With only 568 miles on my truck this is my oil level. I’m calling the dealership tomorrow. Very frustrated that I’m dealing with this on a brand new vehicle.
I have wondered this as well. I definitely hear an electronic whirring sound from what sounds like the passenger fender or firewall area. Definitely when I open the door, and other random times as well.Has anyone confirmed that the sounds from the truck when off is actually the fuel pump priming?
How about after the driver door is closed and a foot on the brake pedal to initiate the prime.Wouldn't there be a software update to reduce the fuel pump priming? Only when the drivers door is unlocked or opened would make sense.
Agreed. Or, since the prime takes 1 second, what my older ranger did: prime as soon as key turn starts. The key turn takes 1/4-1/2 second, I'm willing to wait an extra 1/2 second for the engine to startHow about after the driver door is closed and a foot on the brake pedal to initiate the prime.
I really doubt anybody checks and smells their oil on a brand new truck, i sure as hell wouldn't have if I didn't find this forum,Ford Ranger sales up 12.38% in the first quarter of 21, 24,083 units sold. It will be interesting to see if this fuel dilution problem expands, is so maybe Ford will finally find a solution!