Just updated to Sync 3.4 on my Ranger 2019

[gmadams]

I only enabled the climate domain. Right after I reset it, the wife took it and went to the store. When she got back the climate icon was there and it seemed to have full functionality. I'm not sure now if I overlooked the climate icon or it wasn't there at that time.

Sponsored

 

[gmadams]

Geoff after you Enabled these 3 settings in the APIM, did you have to perform a module reset using FORScan or a Master Reset?

I did a master reset. All that did was losing all my presets. It didn't do anything as far as enabling the climate icon.

 

[tmcolegr]

I'm still curious why some only had to Enable Climate Domain while others had to Enable both of the Climate Icons as well: Mode and Recirculation

 

[Geoff]

I'm still curious why some only had to Enable Climate Domain while others had to Enable both of the Climate Icons as well: Mode and Recirculation

I think some folks enabled all three because that's the default. To my knowledge it has yet to be shown if that is needed or not.

 

[Gizmokid2005]

Finally talked to my dealer again. They heard back from Ford and actually have a bulletin for it now, but no fix from them, "it's a software issue they're working on" and I need to call them back in 3-10 days.

*sigh*

 

[Geoff]

Finally talked to my dealer again. They heard back from Ford and actually have a bulletin for it now, but no fix from them, "it's a software issue they're working on" and I need to call them back in 3-10 days.

*sigh*

One small step for man....one large step for Ford....

 

[Gizmokid2005]

One small step for man....one large step for Ford....

Seriously. This can't be that hard to fix? What am I supposed to do in the meantime? Not touch my climate? kthx.

 

[mtbikernate]

Seriously. This can't be that hard to fix? What am I supposed to do in the meantime? Not touch my climate? kthx.

Probably should have waited like I am. Climate controls on my v3.3 work fine.

 

[Gizmokid2005]

Probably should have waited like I am. Climate controls on my v3.3 work fine.

Hindsight is 20/20.

 

[Ace Holliday]

Seriously. This can't be that hard to fix? What am I supposed to do in the meantime? Not touch my climate? kthx.

It sucks but you still have the buttons. So you can adjust with those right?

 

[MotoWojo]

I think some folks enabled all three because that's the default. To my knowledge it has yet to be shown if that is needed or not.

Just for reference I updated my Sync to 3.4 and did not lose my on-screen climate controls. I did go into Forscan and played with splash screens and I did notice, while I was in there, that all three were enabled on mine by default.

To be honest, I do not use the on-screen climate controls much, because when I do, to direct air flow to say just the floor, the flow goes down to almost nothing and I end up changing it back to auto.

 

[Gizmokid2005]

It sucks but you still have the buttons. So you can adjust with those right?

Yeah, I can control temp and "mode" but not dual climate control on or off or what vents are being used.

 

[Geoff]

Just for reference I updated my Sync to 3.4 and did not lose my on-screen climate controls. I did go into Forscan and played with splash screens and I did notice, while I was in there, that all three were enabled on mine by default.

Thanks....same here as well.
That said, I would have enabled all 3 if I had lost climate.

 

[Geoff]

Seriously. This can't be that hard to fix? What am I supposed to do in the meantime? Not touch my climate? kthx.

Next time you talk with with Service Writer ask him what he thinks of 'reloading the APIM AS-Built data'.
This is easily doable by the dealer and I'm pretty darn sure it will restore the climate screen.

 

[VAMike]

Next time you talk with with Service Writer ask him what he thinks of 'reloading the APIM AS-Built data'.
This is easily doable by the dealer and I'm pretty darn sure it will restore the climate screen.

Isn't the problem that the as builts are wrong?

Sponsored