Auxillary switch panel

[uberlisk]

Hello, I find this switch panel on the internet. Where can I buy this component?

Sponsored

 

[Nat]

this a stock aux switch option, came on my Tremor, and wired to aux fuse box/harness. Maybe ford accessories has some kinda option?

 

[Yama_Ranger]

FWIW, I have this setup and really like it. Super clean, factory looking install. Runs all my lights and ARB compressor

https://sdhqoffroad.com/products/19...system?_pos=3&_psq=Ranger+switch&_ss=e&_v=1.0

 

[subquark]

For just a few switches, this seems like a handy approach. It's just a plate, you have to do all the wiring and add the switches.

https://caliraisedled.com/products/2019-2021-ford-ranger-switch-panel-4

 

[Colo_Ranger]

Hello, I find this switch panel on the internet. Where can I buy this component?

This is called the up-fitter switches. They are factory on the Tremor, In the States, there is no part number and the part cannot be purchased separately. It appears you're in another country, so you may be able to find it at a dealer, but we cannot get it.

 

[SDXLT]

I found this on Etsy and it’s working great for me.

https://www.etsy.com/listing/1221087943/ford-ranger-togglerocker-switch-panel?ref=share_v4_lx

 

[SVTPaul]

Depending how much you want to spend, the Trigger 6-Shooter is a nice option to check out. It has a wireless controller unless you want switch backlighting (I did), and even then just a single light gauge wire pair to the base. The switch bank sits on a magnetic base so you can take it outside the cab and use it. No wires to pass through the firewall and looks like a factory option. Love mine

 

[KYFord4x4]

I know this is an older thread...but...

Is there an easy way from the top of the dash, where the tray is, to run a wire down so I can install an accessory (USB) power point or switch panel? I don't see a feed through point, can't see any light coming out the top when I put a flashlight under there. Would I have to run the wire across to the feed through for the A-pilar?

 

[AzScorpion]

I know this is an older thread...but...

Is there an easy way from the top of the dash, where the tray is, to run a wire down so I can install an accessory (USB) power point or switch panel? I don't see a feed through point, can't see any light coming out the top when I put a flashlight under there. Would I have to run the wire across to the feed through for the A-pilar?

Here's a couple of threads you can look through. They should have the pictures and areas to tap into that you're looking for to run the wire.

https://www.ranger5g.com/forum/threads/dash-tray-removal.3178/

https://www.ranger5g.com/forum/threads/dashboard-wire-routing-help.26475/page-2#post-609531

https://www.ranger5g.com/forum/threads/wireless-charging-install.2704/page-2#post-166996

 

[KYFord4x4]

Thank you kindly!

 

[veedubtuner]

This is called the up-fitter switches. They are factory on the Tremor, In the States, there is no part number and the part cannot be purchased separately. It appears you're in another country, so you may be able to find it at a dealer, but we cannot get it.

Actually you can buy just the switch panel, it's just pricey ?. As far as the wiring and fuse/relay block, that may need to be custom.

 

[Colo_Ranger]

Actually you can buy just the switch panel, it's just pricey ?. As far as the wiring and fuse/relay block, that may need to be custom.

When I posted that… you couldn’t. Lol

amazing how proud they are of that switch though.

 

[veedubtuner]

When I posted that… you couldn’t. Lol

amazing how proud they are of that switch though.

Yea I didn't notice how old the post was till after lol. My bad.

 

[LawnMM]

You can buy all of it now, I believe, but it's several thousand bucks total if I remember when I did the rough math. Like more than the Tremor package costs when you're buying the truck...

You're better off adding an aftermarket switch/button panel and running some wire and some relays and fuses yourself.

There are several members here with pretty sophisticated setups.

 

[AzScorpion]

Yea I didn't notice how old the post was till after lol. My bad.

Don't feel bad Morgan Paul @OrangeStreak loves to resurrect 4-5 year old threads too. The last one was a 4th of July thread from 4 years ago thinking it was the current year one. ?

Sponsored