Tremor Specific Parts Thread

[LevittownFordParts.com]

The rear leaf springs priced at $342. Is that per side or does that include both right and left? I see it says quantity one but not sure if that's one set or one side. @LevittownFordParts.com

Hi Jake,

Each, x2 are required

Thank you,
- Benny

Sponsored

 

[JDowns]

@LevittownFordParts.com

Tremor Aux Switch Parts.

Switch Assembly (6 switches) - HC3T-13D734-AD

Topper Tray - No standard Ford number but the following: UF1CE, 21044A92-AABZHE (This shares a common dash tray part number), PP-MD20 (Injection Molding Specific), Ford P375 - 1P Topper Tray

Topper Tray Bracket - HB3B-21044A92-PIA-02

Wire Harness - HB3T-14A104-AAAA. There may be more wiring. This is just at the connection of the 6 Switch Assembly.

 

[LevittownFordParts.com]

@LevittownFordParts.com

Tremor Aux Switch Parts.

Switch Assembly (6 switches) - HC3T-13D734-AD

Topper Tray - No standard Ford number but the following: UF1CE, 21044A92-AABZHE (This shares a common dash tray part number), PP-MD20 (Injection Molding Specific), Ford P375 - 1P Topper Tray

Topper Tray Bracket - HB3B-21044A92-PIA-02

Wire Harness - HB3T-14A104-AAAA. There may be more wiring. This is just at the connection of the 6 Switch Assembly.

Thanks Jeff,
But I cant get these part numbers to populate. I also tried to cross reference them as engineering numbers to part numbers but no luck. I am not sure why these parts are being kept hush hush but I will try running them through again soon.

- Benny

 

[JDowns]

Thanks Jeff,
But I cant get these part numbers to populate. I also tried to cross reference them as engineering numbers to part numbers but no luck. I am not sure why these parts are being kept hush hush but I will try running them through again soon.

- Benny

No problem.

I had the parts apart this afternoon to measure the switches and get the connector part documented for a pigtail extension as I'm considering relocating them above the sunglass compartment to free up the dash space for another project. Those are the part numbers directly out of my vehicle.

At least the 6 switch part is common across trucks.

Regards,

 

[LevittownFordParts.com]

If you install the Tremor Aux switches, don't forget the higher output Tremor generator / alternator to go with them...

Does anyone have the part number for that alternator? Ford won't tell me... it's a national secret...

Surprisingly this part actually shows up in our dealer data, The part # is HB3Z-10346-A

-Benny

 

[LevittownFordParts.com]

Thank you Benny!

I've been searching for specs / part number for that alternator since I purchased my truck... I will be adding one of these to my spares box...

That's a big help!

You wouldn't also have the higher CCA rated battery part number? I've been testing mine (truck purchased in June) due to recent low voltage warnings... seems it's bad. Will take a charge but doesn't hold under load. Charging system voltage is OK at 14.4V, but again, my battery doesn't hold voltage under load. Also, I've noticed a voltage reduction after fully charging then resting over a week... goes from 12.65V to 11.9V after removed from vehicle while sitting on a wooden work bench.

Sure, Here is what I show

760 amp BAGM-48H6-760
800 amp BAGM-94RH7-800

Please let me know if you have any questions.
Thanks,
-Benny

 

[HMG03]

@LevittownFordParts.com So according to the dealership, my Tremor was shipped without the 100 amp fuse need to power the Upfitter Switches so I can use my ditch lights. I connect my lights to the hot wire coming from the aux fuse box, ground the lights to the battery, and nothing works. Engine running and everything. I touched the power lead to the positive and negative terminals of the battery, and the lights work just fine. The tech said that the wiring is there, just no fuse. What is he talking about? Is there a part number for this, and where is it located?

 

[LevittownFordParts.com]

@LevittownFordParts.com So according to the dealership, my Tremor was shipped without the 100 amp fuse need to power the Upfitter Switches so I can use my ditch lights. I connect my lights to the hot wire coming from the aux fuse box, ground the lights to the battery, and nothing works. Engine running and everything. I touched the power lead to the positive and negative terminals of the battery, and the lights work just fine. The tech said that the wiring is there, just no fuse. What is he talking about? Is there a part number for this, and where is it located?

I looked through the fuses listed and none of them were 100Amp. I did come across this circuit breaker which is located in the smart junction box which I believe is under the hood on these trucks.


Part # DG9Z-14526-AA

-Benny

 

[JDowns]

According to the manual in the "High Current Fuse Box" fuse #5 is the "Auxiliary Fuse And Relay Box" 100A.

 

[LevittownFordParts.com]

According to the manual in the "High Current Fuse Box" fuse #5 is the "Auxiliary Fuse And Relay Box" 100A.

This sounds like a completely separate fuse box then. I wish my data showed this so I can help clarify but its not there.

- Benny

 

[JDowns]

This sounds like a completely separate fuse box then. I wish my data showed this so I can help clarify but its not there.

- Benny

From the manual on Page 248.

"High Current Fuse Box"

"Your vehicle has a pre-fuse box in the engine compartment below the engine compartment fuse box. This box contains several high current fuses. If replacement of these high current fuses is required see an authorized dealer".

Page 257 then shows it under the main engine compartment fuse box. No instructions on how to get under there, just shows an arrow and (5) fuse locations.

If it helps, if I do a lookup on my VIN thats the same 100A circuit breaker listed,

 

[HMG03]

I looked through the fuses listed and none of them were 100Amp. I did come across this circuit breaker which is located in the smart junction box which I believe is under the hood on these trucks.


Part # DG9Z-14526-AA

-Benny

Ok, so what I am looking at in the picture is the underside of the fuse box as it is mounted in the truck, right? I know there are 2 sides to that fuse panel.

 

[LevittownFordParts.com]

Ok, so what I am looking at in the picture is the underside of the fuse box as it is mounted in the truck, right? I know there are 2 sides to that fuse panel.

Based on what Jeff found in the owners manual what your looking for is a Tremor specific fuse box so I do not believe the one I posted is correct and I do not have any diagrams or photos to share. Maye a Tremor owner can confirm and post a pic?

- Benny

 

[HMG03]

Based on what Jeff found in the owners manual what your looking for is a Tremor specific fuse box so I do not believe the one I posted is correct and I do not have any diagrams or photos to share. Maye a Tremor owner can confirm and post a pic?

- Benny

So I took the truck to Smith Cairns Ford and let the mechanic take a look. He had me come in and show him exactly what was wrong, and we confirmed that it is not the green fuse, but it's one of the knife-type fuses that are in the High Current box. There is a 4th power supply that is connected, but there's no fuse installed where the harness pigtail would attach to the power distro plate inside the box. We took a look at another Tremor that they had on the sales lot, and that Tremor had the fuse that I didn't have in mine. He showed me the page in the service manual for the High Current Fuse Box, and the part was labeled "F5" on the screen, but we couldn't find a part number when we spoke to the Parts Dept. I will try and take a pic that next time I am out in the truck. They took a bunch of pics, and are consulting some kinda Engineering Department about getting a number, or if the harness has to be replaced. Do you know of any possible part numbers?

 

[JasonTremor]

I was looking to see if my tremor had all the towing package fuses and while I had the fuse panel flipped up I took a pic. Maybe this will help. I believe you are referring to the 100 amp fuse on the right.

Sponsored