What did you receive in the mail today for your Ranger?

[Whiplash]

The missing pieces to complete my full mid travel suspension make over......APG
Billet tie rod ends, with FK Bearing Heim joints......more articulation, less stress on all the other moving parts my mid travel conversion involed..

.

Sponsored

 

[DukeCanBuildit]

Was expecting these on December 16. Surprised when the doorbell rang this morning.
56” heavy duty, full extension, 3 position-locking, drawer slides. Have a little project planned…

Hmmmm, is someone building their own Decked System? I sure hope so. Post a thread if you do. ?

 

[Danager]

Hmmmm, is someone building their own Decked System? I sure hope so. Post a thread if you do. ?

Building a slide for 1/2 the width of the bed. Will hold the Yeti Tundra 105, and Firman inverter.

 

[JohnnyO]

Blue grille letters.

 

[Jbroke]

Service Reminder from my Dealer...good price on the Works Package

That's a steal until the $500+ worth of "recommended" maintenance that they will highly suggest and should be done shortly or else your truck may fall apart

 

[OrangeStreak]

That's a steal until the $500+ worth of "recommended" maintenance that they will highly suggest and should be done shortly or else your truck may fall apart

Yep...I've dealt with that gimmick a few times After an inspection, one service center said I needed to replace the cooling system hoses to prevent any future issues and I didn't do it because I checked them and they were fine...the hoses were still intact when I traded that truck in! I'm still on warranty now so if anything covered under it needs to be fixed it will be on their dime

 

[JohnDLG]

Some magnetically attached battery powered LED lights for the bed of my truck, I have a tonneau cover so its dark in there at night. They fit nicely right under the rear tie downs by the tailgate.

https://www.amazon.com/dp/B00UMSEP0Q/?tag=facebook04ca-20

 

[ControlNode]

FedEx if finally showing the manuals out for delivery, they were only due last Wednesday.

Update: And the CD install fixed my access to the Focus service manual that broke when I had to reset Windows before the Windows 11 upgrade. Yes, I copy the disk to my HD and update the tsobrowser.ini because waiting on the data to load from the CD is a waste of time. And my laptop doesn't have an internal CD drive so having it at the car with a USB CD drive connected is cumbersome. I had put my Focus CD in a really safe place, but so safe I can't even find it to reinstall. So this Ranger FSM install fixed that as well.

 

[Jrel209]

Just received my morimoto headlamps and tremor flares finally painted!! Hopefully decent weather this weekend to get them installed

 

[Colo_Ranger]

Building a slide for 1/2 the width of the bed. Will hold the Yeti Tundra 105, and Firman inverter.

Are you planning to drill mounts through the bed? I have a few ideas, but I really, really don't want to drill through the bed.

 

[AzScorpion]

Some more detailing goodies finally showed up today. The Graphene detailer along with a few others that I'm running low on. The battery maintainer is for my Jeep and I figured I'd try this one out as it was a good price. I always throw in another bag of microfiber towels, you can never have to many right Duke @DukeCanBuildit. ?

 

[DukeCanBuildit]

Some more detailing goodies finally showed up today. The Graphene detailer along with a few others that I'm running low on. The battery maintainer is for my Jeep and I figured I'd try this one out as it was a good price. I always throw in another bag of microfiber towels, you can never have to many right Duke @DukeCanBuildit. ?

Nope, never enough. I always take a few along, just in case.

 

[AzScorpion]

Nope, never enough. I always take a few along, just in case.

Rookie! ?

 

[Ds_2020Ranger]

Some lights arrived today

 

[Danager]

Are you planning to drill mounts through the bed? I have a few ideas, but I really, really don't want to drill through the bed.

Because I’m only going 1/2 the width, I cannot run a mount the full width of the bed. I am planning to install plus nuts, which are wider than rivnuts. I want this to be somewhat easy to remove. I also need this to be as low as possible, which means the brackets will be installed in the troughs of the bed.

I’m on vacation as of 7pm today. Over the next few days, I plan to mock this up and take the measurements for some t-slot extruded aluminum for the perimeter of the base.

Sponsored