Remote Transmission Dip Stick Aftermarket Support?

[RCMUSTANG]

Still need one to verify the level is correct with the deep pan. Anxiously waiting...

Sponsored

 

[Racket]

Unlike @Grumpaw who has graciously said he'll sit out the first round ? I'm all in. I expect you'll be making - if it isn't some extreme personal distraction - more once word gets out.

As small as our forum is I would suspect the Bronco crowd is going to hit you up, especially since some members have one. I'm sure the design wouldn't be exactly the same.

I'd expect the Mustang enthusiasts wold be all over one too though you'd be in a similar boat.

Hell, pick the most likely group of 10R80 equipped car owners by volume sales and aftermarket vendors.

Lincolns seem to be leased more than kept long term so you know the interest there would be nil.

 

[lthom]

I'm somewhere on the list. Mid pack I think. I'm willing to wait. I'm just at 5000 miles with verified full transmission fluid level. I'm very impressed with your dedication and skill set. Thank you for all your efforts.

 

[Fitzmotor]

Still need one to verify the level is correct with the deep pan. Anxiously waiting...

The pan does not make a difference in marking the level, the full mark is the full mark, no matter what the volume is, so bigger pan, smaller pan, it's all the same full level.

And yes, if this is a hit I want try others, Bronco, F150, whatever.

 

[Grumpaw]

Unlike @Grumpaw who has graciously said he'll sit out the first round ? I'm all in. I expect you'll be making - if it isn't some extreme personal distraction - more once word gets out.

As small as our forum is I would suspect the Bronco crowd is going to hit you up, especially since some members have one. I'm sure the design wouldn't be exactly the same.

I'd expect the Mustang enthusiasts wold be all over one too though you'd be in a similar boat.

Hell, pick the most likely group of 10R80 equipped car owners by volume sales and aftermarket vendors.

Lincolns seem to be leased more than kept long term so you know the interest there would be nil.

Gracious !!! Gracious !!!! HA !!! I'm just as impatient as is everyone else.....
But, I do have a B&M, and there were many on "The List" before me, so I'll wait my turn....
Call me "Graciously Grumpy" ...

 

[JesseS]

Too bad the votes are not dated or it would be easy, because not everyone who voted yes also posted at the same time post dates could be off also. You could pre-announce the opening of orders sent to the new companies email and just send out the ones not pre-allocated, leaving you with a solid list by order time/date, for the next batch. Just spit-balling here

 

[RCMUSTANG]

The pan does not make a difference in marking the level, the full mark is the full mark, no matter what the volume is, so bigger pan, smaller pan, it's all the same full level.

And yes, if this is a hit I want try others, Bronco, F150, whatever.

I know. I just an m want to be sure they refilled it with enough.

 

[Stevedbvik1]

“I want it all, I want it all, I want it all and I want it now!”
-Queen
?

 

[melficeapoll]

Getting closer and closer to the release of the long awaited 19-23 Ford Ranger MBS Trans Dipstick!!!????

 

[Msfitoy]

Actually, I had to figure out what to do with a shirt with a hole in it, it was new but you can see a hole in the front below the text, that's when I thought I would be funny and quote you on a shirt, nobody got it though, even you.... failed humor

Your shiny object is so bright we couldn't see the T-shirt lol...

 

[JesseS]

Your shiny object is so bright we couldn't see the T-shirt lol...

UH... TMI !

 

[The Last Ranger]

Finally a update about some real progress!

I'm still just a little ways out, but I'm a bunch closer, I have the parts finally, I still have to have the hoses made and I'm waiting on the stamp and ink for the handle.

They came out nice, the anodizing looks good and they fit the engine bracket well.

The top fitting will probably have to be machined where the stick goes in, to adjust for the hose length variation, that still has to be determined, I'll know exactly when I get 60 hoses in hand.

I threw in the logo, MBS or "Mike's Build Shop", I actually started a company, it was the logical thing to do, I can order stuff at better pricing, as well as other benefits, plus branding and image goes a long way vs a no name blank part.

Next week things should really start to move along, I hope everybody still has interest and haven't given up, it sure has been a painfully long process. View attachment 192150 View attachment 192151 View attachment 192155 View attachment 192156

Ok your killing me with this awesome setup, I want one and the money is ready to send. I should be on the list and I can't wait to install and look at my tranny fluid level. Funny thing is I usually look at the levels cold and remove the fluid and refill and run the tranny and check my level when its cold and if its the same I figure its good. And yes I know its not the proper thing to do so maybe this time I will check when hot to do it right.

 

[Fitzmotor]

Just a few pics, I spliced a hose to do a fit, fits as planned.

 

[ctechbob]

I've run out of superlatives. ?

 

[stinkechin]

Just a few pics, I spliced a hose to do a fit, fits as planned.

God lord that looks good.

Sponsored