Am I missing a Wheel Well Liner?

[Chris M]

I be damned....you are correct. Dave's is just black paint.

Yep.
And mine is gray and uncovered. Looks like a really nice place for a liner to have been.

Sponsored

 

[DakotaGuy]

Bumpers may be worth it...they'll firm up the hood, no bouncing, thus smoothing out the air flow over the front...probably good for 7-10 horsepower !!!

The funny thing is I honestly think the hood bumpers and weather stripping wasn't deleted to save costs, but left off because of supply issues. I have a 2022 built in March 2022 and I have the little hood bumpers and all the hood weather stripping yet some built before mine don't have it. I think even though they were missing those small items they just built and shipped.

 

[LB'sTremor]

^^^^ Tremor built 02/22 I have weatherstrip and no bumpers
LB

 

[Ranger X]

?‍ So far all the pics look the same to me.

Anyone with an arrow pointing to the missing piece ?

They are all the same, AZ Scorpion’s only difference is the color of the sheet metal.

 

[LB'sTremor]

OK I am losing sleep over the hood bumpers, do these look correct? Product Details | SimplePart (lakelandford.com) Still not sure what to do about the liner that is missing, or is it?

This Forum drives me nuts! haha

Thanks,
LB

 

[OregonRangerTremor]

OK I am losing sleep over the hood bumpers, do these look correct? Product Details | SimplePart (lakelandford.com) Still not sure what to do about the liner that is missing, or is it?

This Forum drives me nuts! haha

Thanks,
LB

Where do these bumpers go? Thanks

 

[paval3]

Where do these bumpers go? Thanks

I was hoping some one would show a photo of theirs so I know what to look for.

 

[Chris M]

I was hoping some one would show a photo of theirs so I know what to look for.

Pics of the hood bumpers are in this thread: https://www.ranger5g.com/forum/threads/bouncy-hood.20935/

Post #38 and following

 

[The Last Ranger]

Well, I ordered the parts and will pick them up at the ford dealer on Friday after 1pm. Sure will be interesting to see what I get. I will update you guys later friday afternoon. I really didn't mind being the ginny pig to figure out this puzzle as the parts were low dollar cost. I also ordered the bumpers and will see how they fit.

Ok I have the parts and as discussed there was no solving the front most liner because it wasn't a liner, just metal. Good news ,one of the parts KB3Z-16103-A was the shield for the oil filter so that could be handy if I happen to destroy mine changing my oil. The other shield KB3Z-16103C is the small front shield that looks like Florida.
The 2 hood bumpers EB3Z-16758-A fit perfectly in the fender square holes as I had to slide them in.
The high side of the bumper toward the outside or high edge of each fender. I have the fiberglass hood with a front deflector and they worked perfectly but I didn't have a problem initially. I'm guessing they may fix an issue if someones hood is slightly loose or vibrational.
Hope this helps.

 

[Muscleford]

Ok I have the parts and as discussed there was no solving the front most liner because it wasn't a liner, just metal. Good news ,one of the parts KB3Z-16103-A was the shield for the oil filter so that could be handy if I happen to destroy mine changing my oil. The other shield KB3Z-16103C is the small front shield that looks like Florida.
The 2 hood bumpers EB3Z-16758-A fit perfectly in the fender square holes as I had to slide them in.
The high side of the bumper toward the outside or high edge of each fender. I have the fiberglass hood with a front deflector and they worked perfectly but I didn't have a problem initially. I'm guessing they may fix an issue if someones hood is slightly loose or vibrational.
Hope this helps.

Thanks. what is part no. KB3Z-16103-B?

 

[The Last Ranger]

Thanks. what is part no. KB3Z-16103-B?

Not sure as I didn't order that one, sorry

 

[LB'sTremor]

I am talking about the bumpers that attach to the fenders not the screw in ones on teh core support. I did not see these in teh other thread (unless I missed them).

LB

 

[RedDakooter05]

I am talking about the bumpers that attach to the fenders not the screw in ones on teh core support. I did not see these in teh other thread (unless I missed them).

LB

You'll see square holes. Since I don't have them either I can't tell you how to install them, but I assume you "snap" or push into place.

edit: Actually based on the images of the bumpers they slide into the t-shaped opening at an angle. Easy process.

 

[LB'sTremor]

yup I got the holes just wondering if those are the correct bumpers

 

[RedDakooter05]

yup I got the holes just wondering if those are the correct bumpers

Should be.

Sponsored