What did you do to your Ranger today?

[Venom_z89]

has anyone else seen that 7 inch lifted ranger on youtube? He uses jeep jl apex sway bar disconnect that works fairly nice. no bolting and unbolting.

Sponsored

 

[Cmar]

Washed it, just come back from a 3 week road trip to the bottom of the country, it was very dirty.

 

[OFC Ranger]

Got a 10 foot shielded harness tapped into the factory rear camera harness so I can relocate the camera up high on the back of my rack. Also started the new (subtle) changes to my matte black graphics.

Its almost as if all the pieces of the puzzle are starting to come together, hmm...

 

[RedDakooter05]

Used a bicycle tire pump to add a few psi to my rangers tires.

Yeah you read that correctly. Pretty effective too might I add.

 

[IdahoRanger]

Used a bicycle tire pump to add a few psi to my rangers tires.

Yeah you read that correctly. Pretty effective too might I add.

Cardio

 

[Metal Geezer]

Finally pulled the trigger on a lower grille insert.

 

[Doc]

Finally pulled the trigger on a lower grille insert.

Nice !

 

[pbethel]

Overnight? They (Ford) must be getting cheap now as they did mine as I waited. I think I was there maybe 45 minutes and out the door. Good luck Lee and hopefully it fails. I know most times you don't want to hear those words but in this case it'll be nice.

When I worked for NAPA we had to attach a printout from the tester to the battery warranty form. No slip, no re-imbursement.
If the tester said to charge and re-test that is what we had to do otherwise the store just gave away a free battery.
Over half the time the battery just outright failed, so no charge and re-test.

 

[RedDakooter05]

Cardio

Aint no tailgate damper user here.
*kisses my bitch boy biceps*

 

[Blmpkn]

Got most of my bed rack on before it started to pour. Hopefully get the crossbars on tomorrow.. but.. supposed to pour so ?‍ well get there eventually lol.

The rack is a haul-master 800lb universal job I snagged at hazard fraught. I ended up cutting 4" off the uprights so the crossbars would be at a reasonable height above the cab. This required enlarging 2 holes per upright a hair and tapping them for m10x1.5.

Easy peasy.

 

[OFC Ranger]

@Msfitoy I think I need to up my font size next time. lol

This turned out to be a PITA. Those are 22 gauge needles...

I had to water down the acrylic to get it to flow out.

The matte clear coating should kill the shiny and discoloration.

 

[Msfitoy]

@Msfitoy I think I need to up my font size next time. lol

This turned out to be a PITA. Those are 22 gauge needles...

I had to water down the acrylic to get it to flow out.

The matte clear coating should kill the shiny and discoloration.

Professional Doc!

 

[WolfgangVTS]

Well, I removed the factory 4x4 decals from the truck bed:

And added gray and black 4x4 decals in their place:

I had actually given serious thought about not putting them on after I removed the factory decals…I really liked the clean look of the bed, but I think the gray and black decals are a nice subtle touch.

 

[DukeCanBuildit]

@Msfitoy I think I need to up my font size next time. lol

This turned out to be a PITA. Those are 22 gauge needles...

I had to water down the acrylic to get it to flow out.

The matte clear coating should kill the shiny and discoloration.

 

[tm1506]

Applied a second coat of 303 Graphene!

Sponsored