What did you do to your Ranger today?

[frederick184]

I've been wondering how that looks on the tray, thanks for posting. Also, if you want the front area to sit flush again, take the tray out and reinstalling placing the front in first then push the back down. I had to do that today when reinstalling mine.

It’s funny you mentioned that because I just did that a few minutes ago because it was bugging me

Sponsored

 

[Colo_Ranger]

It’s funny you mentioned that because I just did that a few minutes ago because it was bugging me

I'm OCD about some things...

 

[Bob902]

I guess I should at least get that, so I can be a part of the elite club. If they'll have me in it...

Don't give in to the purse toters!!!!



Viva la Resistance!!!!!

 

[underwhelmed]

I guess I should at least get that, so I can be a part of the elite club. If they'll have me in it...

If you want to publicly acknowledge your low T and ED the damper is the best way to come out…????

 

[AzScorpion]

I guess I should at least get that, so I can be a part of the elite club. If they'll have me in it...

Now you're talkin'! Everyone's welcome especially the holdouts. It makes sending the t-shirt that much sweeter. ?

 

[AzScorpion]

Don't give in to the purse toters!!!!



Viva la Resistance!!!!!

Shush You! Don't listen to him Chris! Bob has no idea what he's missing.

 

[AzScorpion]

If you want to publicly acknowledge your low T and ED the damper is the best way to come out…????

It's not like we're all sitting around drinking this? Well, at least not all of us. ?

 

[scarchild35]

Now you're talkin'! Everyone's welcome especially the holdouts. It makes sending the t-shirt that much sweeter. ?

Oh I'd be honored, haha.

 

[Dr. Zaius]

Shortened the bed rack rails that I recently installed to better fit my truck.

Removed 8.25 inches off of them.

Fits much better.

Also installed my Air Design fender vents.

Before

The factory vents are held on by adhesive on the rear edge and clips around the perimeter. The Air Design vents just use the 3M molding tape.

And the After pic

 

[MrBusses]

Installed a 12V plug in the bed. I used a ford male connector and a $8 12v plug from amazon. I had to Dremel the hole slightly bigger to get it to fit and I used some right angle spade connectors on the back otherwise it would hit the inner fender. I was originally going to use the top square hole but it wasn't deep enough, I still might move it to a lower position but my hole saws are at work. The pig tail cost me $25 with my employee discount and the out let was $8 on amazon. link for the plug https://a.co/d/dIMqtO3 I also attached the wiring diagram for the plug C243 is the connector under the truck and the connector that is needed.

 

[RedDakooter05]

Debated what to do about this

This f'ing truck lmao. Fantastic quality bumper to bumper.


Ah well.

 

[Synfulz]

I gave it a very thorough wipe down and cleaning everywhere. The wheelwells, suspension, under the hood, and of course body. As I am getting my 2nd oil change tomorrow. They do a thorough inspection on intake. So if all clean makes it easier to see I have no scratches, or damage.

 

[AzScorpion]

I gave it a very thorough wipe down and cleaning everywhere. The wheelwells, suspension, under the hood, and of course body. As I am getting my 2nd oil change tomorrow. They do a thorough inspection on intake. So if all clean makes it easier to see I have no scratches, or damage.

Pics? We need pictures! ?

I guess it's true that Mall Crawlers get dirty and need detailing too. ??

 

[RedDakooter05]

I gave it a very thorough wipe down and cleaning everywhere. The wheelwells, suspension, under the hood, and of course body. As I am getting my 2nd oil change tomorrow. They do a thorough inspection on intake. So if all clean makes it easier to see I have no scratches, or damage.

They care if someone has scratches on their intakes?

 

[Synfulz]

Pics? We need pictures! ?

I guess it's true that Mall Crawlers get dirty and need detailing too. ??

Sponsored