What did you do to your Ranger today?

[r1ch999999]

I want one of those tool boxes.

Sponsored

 

[Jake596]

I want one of those tool boxes.

If you havent used your FordPoints yet it about covers it, I paid $23 out the door with my pass points at my local dealer, showed up the next day, easy install.

 

[P. A. Schilke]

Hi Folks,

I added door edging to the Lincoln Nautilus to help my poor little Ranger from getting door dings from the Nautilus...Ranger ding prevention....

Best,
Phil Schilke
Ranger Vehicle Engineering
Ford Motor Co. Retired

 

[Glocker]

This made for a long, hot day! Thanks a billion to my wife who found this tonneau cover on Amazon for $735!!! And I'm indepbted to my good friend who gave up a huge chunk of his day to help me install it!

And I jumped in my buddy's race car after we installed the cover. Damn this thing is ridiculously cool! 2009 body with a 2017 Coyote V8 just swapped into it. This thing is all race car. It was fun climbing in and out of it around the full cage! LOL

 

[Deltasix109]

MOLLE Tech Pouches from BuiltRight Industries. Installed behind rear seats, using it to store all the stuff i had back there (recovery gear, tie down ropes, some basic tools, tie wraps ...). They look great, sturdy and well designed.

This looks really great! Seats lock up no problem, I'm assuming?
Smart use of space

 

[HTX1811]

Been doin all kinds of stuff to the lil Ranger, heres the Hi-lift mounted, bed sprayed, swing out tool box and winch prep, just waiting on my 589FAB mount...tick Tock..

I think that is as good a spot to mount it as anyone has come up with yet to mount the jack. Looks like you used the factory holes to mount the brackets? Was it tedious but not difficult like I said?
I am going to try to use my points to get the bed tool box next week.

 

[Jake596]

I think that is as good a spot to mount it as anyone has come up with yet to mount the jack. Looks like you used the factory holes to mount the brackets? Was it tedious but not difficult like I said?
I am going to try to use my points to get the bed tool box next week.

Well I had to loosen up the wheel well liner, I got tired of fishing thru the factory hole, but non the less I used your picks for guidance, so thanks again and it turned out nice and solid. The tool box literally takes about 8 minutes to install if your using a small impact.

 

[Michel Jeanneau]

Hi Folks,

I brought home our new Lincoln Nautilus to get acquainted with the Ranger parked next to it. Last I left them, they were talking to each other .... Getting used to knowing each other as they are both very nice products of the Ford Motor Co.

Best,
Phil Schilke
Ranger Vehicle Engineering
Ford Motor Co. Retired

 

[FULLSCALE]

Finally put my bike rack on for the first time and went for a ride with my wife and daughter, Her Burley trailer fits in the bed with all kinds of space under the cover.

 

[weasel1]

Picked up a bed extender for a sport trac. Got some work to do to make it fit!

 

[RedlandRanger]

Got em clean up for its first show of 2020!!!!

You are having car shows? They are being cancelled around here.

 

[jerrywin]

Ford branded bedrug install.

Here's what i did with the tonneau cover drains:

 

[AnimeRanger87]

You are having car shows? They are being cancelled around here.

Some are getting canceled around my area of Central and Southeastern Indiana but some do go on. This show had of 150 cars and trucks show up.

 

[Mr D]

Installed the Weathertech floor mats for the driver and front passenger this morning. While fooling with the truck, I realized I fell into the group that is missing the center bed tie down brackets, and I cannot completely lower by tailgate with my bike rack installed.

I like the floor mats where did you purchase? I but a harbor freight hitch extender on my bike rack.

 

[LogansDad79]

Installed injen intake and lariat engine cover

Sponsored