OFC Ranger
Well-Known Member
- Thread starter
- #1
...to relocate it to the rear of my rack up higher. Appears to be just standard 22 gauge wires feeding the various items. Anything I should keep an eye out for?
Sponsored
I'm about to cut the wires on my factory backup camera...
- Thread starter OFC Ranger
- Start date
- Watchers 4
Figarou
Well-Known Member
...to relocate it to the rear of my rack up higher. Appears to be just standard 22 gauge wires feeding the various items. Anything I should keep an eye out for?
Nah....you're good.
I'll help keep them in. ?
OP
OP
OFC Ranger
Well-Known Member
- Thread starter
- #4
The harness for our Ranger is only 5 pin behind rear emblem.
Plug and play from Rostra , if you dont want to snippy snip...
Also, why pay when I have the tools and material to make my own harness.
NotBudule
Well-Known Member
well I did not know that you have/could ... carry on sir !The harness for our Ranger is only 5 pin behind rear emblem.
Also, why pay when I have the tools and material to make my own harness.
Dahveed
Well-Known Member
- First Name
- David
- Joined
- Aug 9, 2020
- Threads
- 9
- Messages
- 468
- Reaction score
- 1,057
- Location
- Central Kansas
- Vehicle(s)
- 2020 Ranger XLT 4x4 / 2020 Ford Edge ST-Line
- Occupation
- Pharmacy Consultant
It plugs in to the connection behind the bumper. Where you disconnect it if you need to remove the tailgate.The harness for our Ranger is only 5 pin behind rear emblem.
Also, why pay when I have the tools and material to make my own harness.
JesseS
Well-Known Member
- First Name
- Jesse
- Joined
- May 26, 2021
- Threads
- 18
- Messages
- 1,686
- Reaction score
- 4,619
- Location
- NorCal (Roseville)
- Vehicle(s)
- 2021 Ranger XLT FX4, Jayco 26' Class A
- Occupation
- Retired, work is a four letter word.
Yep! Like all of 12v, a real killer!high voltage.
Ranger_Rocks
Well-Known Member
OP
OP
OFC Ranger
Well-Known Member
- Thread starter
- #11
Pro tip, thats just a bigger harness that ties in with the rear power gate lock wiring.
The camera is 5 wires. Easy snip snip to add in extension I need.
Highlander
Well-Known Member
- First Name
- Frank
- Joined
- Feb 3, 2022
- Threads
- 11
- Messages
- 565
- Reaction score
- 2,575
- Location
- Nova Scotia, Canada
- Vehicle(s)
- 2021 Ford Ranger Shadow Black Lariat 501A TREMOR
- Occupation
- Private
- Vehicle Showcase
- 1
ctechbob
Well-Known Member
I figured it might be, and looking at your picture I see that it is. There's a set of twisted pair wires there. You'll want to make sure you use a similar setup on your extension wire. Those will be the data/signal wire from the camera. They're done like that to reduce noise in the circuit.
OP
OP
OFC Ranger
Well-Known Member
- Thread starter
- #14
Here or there. I don't care if the guide lines are out of wack, never use them anyhow. Ill rig up an angled bracket.
NotBudule
Well-Known Member
If its mounted in the middle i would think the lines would stay pretty close , might end up being a better angle from up there ...Here or there. I don't care if the guide lines are out of wack, never use them anyhow. Ill rig up an angled bracket.
Sponsored
