What did you do to your Ranger today?

[micl9]

Replaced the factory running boards with Westin HDX Drop Step bars and put on Bushwacker Rocker Panel Sill Protector.

Nice!
I was looking at those also, but found a great deal on a used set of Power Steps.

Sponsored

 

[Stevie Gee]

They look nice. good contrast, how about an overall side view snapper.

Here u go

 

[TopoRanger]

20% tint on all the doors and back glass then 35% on the windshield. Trying to plan ahead and keep the truck cooler. Hoping this helps fridge not work so hard when I finish the rear seat delete and it moves inside the cab.

 

[Dbuster]

Gatorhyde bed liner

 

[JJ101]

Purchased and installed a ReadyLift 2” leveling kit through my Ford dealer. Yep, they also did the alignment and adjusted the headlights. I like it, a little bit of rake, just like I wanted.

 

[Ugly_Betty]

Picked up my birthday present from the wife today…

Been eyeballing those lately.

 

[TVRangerSTX]

Got the Ranger a new garage-mate today, traded the wife's 17 Escape for a 21 Escape. This one's Star White, her old one was Platinum White. But I see they are chiseling cost and features all over at Ford...Old vs new - lost the engine cover, a driver's seat rear pouch, and a cargo cover! Same trim levels, both Titanium. That's all I found so far, and of course, it doesn't have bed tie-downs...
I'm really surprised at the fraternity (if I can use this term here) on this forum...like I told a certain Gregg from Loiusville (where these Scapes are made)...in my early teens I had a Honda 90 and their jingle was "you meet the nicest people on a Honda"... but I think you meet the nicest people on this Ranger Forum!

 

[Danager]

Spent some time getting a switch (for bed lighting), and a couple SAE connectors (one constant power, one switched). The green & black wire in the photo is for the led strip lights for the bed. Need to get the paint marker out to paint the stainless steel screws black.

 

[Ugly_Betty]

No shoes!! Thanks @Discount Tire for the install.

 

[Rainhoffmn]

Installed passenger side pivot case
Thank you ford pass rewards points
Love this thing already
Moving the tie downs were a pain in my ass from the toughbed spray in liner in the threading
But we got her in eventually

I have been Jonesing for this. How many points did it take, if you don’t mind me asking? I don’t want or need the full bed box. Just a place to put some useful things.
thanks

 

[OFC Ranger]

Here u go

Brings back memories. I did that on my old street legal 1000cc China-Buggy before I gave it a new paint job. 5-speed manual, roughly 60 miles to the gallon and would top out at about 85mph. Expression on peoples faces on the interstate when this ugly little thing went buzzing by was priceless.

And just for anyone whos calling BS cause they couldn't figure out how to get a plate for their Polaris RZR's in Georgia, see second picture. You just were not clever enough!

 

[Hickesy]

No shoes!! Thanks @Discount Tire for the install.

Are those the 4S? And looks like you have a lift/level too?

 

[Ugly_Betty]

Are those the 4S? And looks like you have a lift/level too?

Yep and yep.

 

[Discount Tire]

Thank you for the shoutout @Ugly_Betty - we appreciate the support! enjoy the new rubber

 

[Grumpaw]

I have been Jonesing for this. How many points did it take, if you don’t mind me asking? I don’t want or need the full bed box. Just a place to put some useful things.
thanks

Find the lowest on line price, which is right at about $200.00 and see if your dealer can match it. Most usually will or come close, but you won't have to pay shipping.
$200.00 ===about 40,000 points.

Sponsored