Sponsored

Balljoint question

Dereku

Well-Known Member
First Name
Derek
Joined
May 18, 2022
Threads
34
Messages
2,946
Reaction score
7,262
Location
Chicagoland Area
Vehicle(s)
2021 Ford Ranger
Occupation
Project Manager
I am nearing 150k and finally started to hear some noises. Im going to do ball joints (or control arms) and tie rods. Does anyone have any experience with the correct part numbers for steel knuckles.

I found lower ball joints and control arms on rockauto. But nothing for uppers that specifically states steel. A few say aluminum but I do not want to assume the rest are for steel.

If anyone has replaced theirs and has some knowledge I would appreciate it.
Sponsored

 

Frenchy

Well-Known Member
First Name
Chris
Joined
Mar 15, 2020
Threads
169
Messages
7,727
Reaction score
11,037
Location
Elizabeth, Colorado
Vehicle(s)
2012 Nissan Frontier, 1994 F150 XL, 2022 Ford Transit
Occupation
Field Service Technician
No experience on my end with these, but I would at least do the checks to see what parts have failed. Might help you save before replacing what doesn't need replacement
 

airline tech

Well-Known Member
Joined
Aug 24, 2022
Threads
28
Messages
4,768
Reaction score
9,115
Location
Midwest - KS
Vehicle(s)
2022 Ranger Lariat-Super Crew, Cactus Gray
Occupation
Aircraft Tech
Ok
The Mid Production (2020)- Change
Was changing the (Knuckle) from Aluminum to Steel

The Lower Contral Arm (Part Number Changed) only to differentiate a different Ball-Joint stud to match the (new steel) knuckle

The Upper Contral Arm - was unchanged

These numbers are from the Ford Parts sites.
I see Rock Auto has different numbers listed
and it appears the UCA - Part Number Changed but the Ford Parts (Cats) do not reflect it:
So looking at Rock Auto
LH: MCF-2603 / Crosses to: KB3Z-3085-B
RH: MCF-2602 / Crosses to: KB3Z-3084-B

So sometime recently they revised the UCA PN.
It comes up within the Ford sites, but however it does not confirm fitment to the Ranger, so it appears to be the lag in getting the system to update, as I have seen in the past - it takes some time.

I will note that other members have reported difficulty in pressing in ball joints and getting them to seat properly (if I recall correctly) and ended up buying the assembly anyway.
I have not had to do anything with mine yet, so cannot confirm the issues.

Front Suspension Parts.webp


Forgot: Tie Rods (Outer)
Pre:
LH: KB3Z-3A130-D / MEF-521
RH: KB3Z-3A130-B / MEF-519

Post:
LH: KB3Z-3A130-E / MEF-3721
RH: KB3Z-3A130-F / MEF-684
 
Last edited:
OP
OP
Dereku

Dereku

Well-Known Member
First Name
Derek
Joined
May 18, 2022
Threads
34
Messages
2,946
Reaction score
7,262
Location
Chicagoland Area
Vehicle(s)
2021 Ford Ranger
Occupation
Project Manager
So the uppers are the same? I thought people had issues with the aftermarket upper control arms having different ball joints for the knuckles?
 
OP
OP
Dereku

Dereku

Well-Known Member
First Name
Derek
Joined
May 18, 2022
Threads
34
Messages
2,946
Reaction score
7,262
Location
Chicagoland Area
Vehicle(s)
2021 Ford Ranger
Occupation
Project Manager
No experience on my end with these, but I would at least do the checks to see what parts have failed. Might help you save before replacing what doesn't need replacement
With the miles I have it is due all new ball joints. If I am going to do one, ill do all. Could be control arm bushings getting soft too, so I would prefer to swap the whole arm. Need an alignment afterwards either way.

Probably will do tie rods for the hell of it. Everything seems solid. But it doesn’t feel as tight as it once was.
 


airline tech

Well-Known Member
Joined
Aug 24, 2022
Threads
28
Messages
4,768
Reaction score
9,115
Location
Midwest - KS
Vehicle(s)
2022 Ranger Lariat-Super Crew, Cactus Gray
Occupation
Aircraft Tech
Ok,
Let me start over here -since the Ford Parts Diagrams are generating my confusion.
I should have checked my usual reference site for clarification on the other sites that still list the incorrect part numbers.

I know we have had numerous threads about the part numbers and what changed. But with Ford not updating all parts IPC's it makes it confusing on what is correct.

The below IPC's show what the others do not - the real part number changes.

Front Suspension IPC.webp


Upper Control Arm:

UCA Part Numbers.webp


Upper Ball Joint:

Upper Ball Joint.webp



Lower Control Arm

LCA Part Numbers.webp


Knuckle IPC

Knuckle IPC.webp


Knuckle PN's

knuckle PN's.webp


Tie Rod IPC

Tie Rod - IPC.webp


Outer Tie Rod PN's

Tie Rod PN's.webp
 
OP
OP
Dereku

Dereku

Well-Known Member
First Name
Derek
Joined
May 18, 2022
Threads
34
Messages
2,946
Reaction score
7,262
Location
Chicagoland Area
Vehicle(s)
2021 Ford Ranger
Occupation
Project Manager
Thanks! That makes sense for the control arms. I would assume the 6/2020 and later parts correspond to the steel knuckles.

What is still confusing is the replacement upper ball joint is for all rangers. There should be 2 different ones. But I am doing full control arms so its fine.

Thanks again
 

airline tech

Well-Known Member
Joined
Aug 24, 2022
Threads
28
Messages
4,768
Reaction score
9,115
Location
Midwest - KS
Vehicle(s)
2022 Ranger Lariat-Super Crew, Cactus Gray
Occupation
Aircraft Tech
It appears the Ball Joint PN - remains the same, but the mounting angle changed to match the mating surfaces (new knuckle to new UCA)
What specific dimensions they changed - IDK.
I am thinking its the thickness of the upper ears - on the 2 knuckles - generating the changed UCA.

So quite possibly that the UCA was revised with a slightly changed (ball joint) mount point to drive it (thicker mount) closer to the new knuckle.
Meaning that the ball joint - when installed (pressed) would set slightly deeper than the OE design.

So an old (PN) UCA with a new (Knuckle) would allow slop in the mounting :question:

I am just (spit-balling) here as I have nothing to back up my theory.
The only way to really tell would be a micrometer measurement of the Knuckles and UCAs.
New vs Old PN's
Sponsored

 
 








Top