Sponsored

Balljoint question

Dereku

Well-Known Member
First Name
Derek
Joined
May 18, 2022
Threads
34
Messages
2,945
Reaction score
7,261
Location
Chicagoland Area
Vehicle(s)
2021 Ford Ranger
Occupation
Project Manager
I am nearing 150k and finally started to hear some noises. Im going to do ball joints (or control arms) and tie rods. Does anyone have any experience with the correct part numbers for steel knuckles.

I found lower ball joints and control arms on rockauto. But nothing for uppers that specifically states steel. A few say aluminum but I do not want to assume the rest are for steel.

If anyone has replaced theirs and has some knowledge I would appreciate it.
Sponsored

 

Frenchy

Well-Known Member
First Name
Chris
Joined
Mar 15, 2020
Threads
169
Messages
7,727
Reaction score
11,037
Location
Elizabeth, Colorado
Vehicle(s)
2012 Nissan Frontier, 1994 F150 XL, 2022 Ford Transit
Occupation
Field Service Technician
No experience on my end with these, but I would at least do the checks to see what parts have failed. Might help you save before replacing what doesn't need replacement
 

airline tech

Well-Known Member
Joined
Aug 24, 2022
Threads
28
Messages
4,765
Reaction score
9,114
Location
Midwest - KS
Vehicle(s)
2022 Ranger Lariat-Super Crew, Cactus Gray
Occupation
Aircraft Tech
Ok
The Mid Production (2020)- Change
Was changing the (Knuckle) from Aluminum to Steel

The Lower Contral Arm (Part Number Changed) only to differentiate a different Ball-Joint stud to match the (new steel) knuckle

The Upper Contral Arm - was unchanged

These numbers are from the Ford Parts sites.
I see Rock Auto has different numbers listed
and it appears the UCA - Part Number Changed but the Ford Parts (Cats) do not reflect it:
So looking at Rock Auto
LH: MCF-2603 / Crosses to: KB3Z-3085-B
RH: MCF-2602 / Crosses to: KB3Z-3084-B

So sometime recently they revised the UCA PN.
It comes up within the Ford sites, but however it does not confirm fitment to the Ranger, so it appears to be the lag in getting the system to update, as I have seen in the past - it takes some time.

I will note that other members have reported difficulty in pressing in ball joints and getting them to seat properly (if I recall correctly) and ended up buying the assembly anyway.
I have not had to do anything with mine yet, so cannot confirm the issues.

Front Suspension Parts.webp


Forgot: Tie Rods (Outer)
Pre:
LH: KB3Z-3A130-D / MEF-521
RH: KB3Z-3A130-B / MEF-519

Post:
LH: KB3Z-3A130-E / MEF-3721
RH: KB3Z-3A130-F / MEF-684
 
Last edited:
OP
OP
Dereku

Dereku

Well-Known Member
First Name
Derek
Joined
May 18, 2022
Threads
34
Messages
2,945
Reaction score
7,261
Location
Chicagoland Area
Vehicle(s)
2021 Ford Ranger
Occupation
Project Manager
So the uppers are the same? I thought people had issues with the aftermarket upper control arms having different ball joints for the knuckles?
 
OP
OP
Dereku

Dereku

Well-Known Member
First Name
Derek
Joined
May 18, 2022
Threads
34
Messages
2,945
Reaction score
7,261
Location
Chicagoland Area
Vehicle(s)
2021 Ford Ranger
Occupation
Project Manager
No experience on my end with these, but I would at least do the checks to see what parts have failed. Might help you save before replacing what doesn't need replacement
With the miles I have it is due all new ball joints. If I am going to do one, ill do all. Could be control arm bushings getting soft too, so I would prefer to swap the whole arm. Need an alignment afterwards either way.

Probably will do tie rods for the hell of it. Everything seems solid. But it doesn’t feel as tight as it once was.
Sponsored

 
 








Top