What did you receive in the mail today for your Ranger?

[DukeCanBuildit]

Even with some tools, kind of a pita, if you've never done it before, I hadn't. So keep the wheels on the ground to get the old links off, it's ten times harder fighting the weight of the linkage and the sway bar if you pull the wheel first.

Then once the old ones are off, loose goose fit the new ones, if the sway bar is a little high you can start lifting the corner with a jack and the weight of the linkage and wheel will pull it down and help you line it up, or vice versa.

Once you have it in and the bolts are on kinda loose, hand tight, etc, if you think with your tools and torque wrench pulling the wheel is worth it, go to it. Definitely necessary for torquing the side that's recessed inside the knuckle.

Honestly don't see how you can torque the other side without a lift or a big set of ramps to give you the room to get at it from below. I recommend gorilla tight and chill.

Comparison photo, super easy to get to the zerk fittings if you just full lock the wheels to the opposite side

My old garage was so small, I would have to move my truck out to get to my floor jack. I replaced one of the OEM links because of a torn boot and I didn’t use my jack. I don’t recall exactly how I managed it but I either loosened the anti-sway bar clamps or simply pried on the end of it and was able to get enough play to line things up.

 

[AzScorpion]

Alex, I'd be more worried when you hear the chainsaw fire up!

 

[Colo_Ranger]

my drain plug arrived today. I’ll be doing my oil changes from now on and this will allow me to leave the skid plates on. Which is nice because I have the ARB and they are heavy.

 

[lariat]

Even with some tools, kind of a pita, if you've never done it before, I hadn't. So keep the wheels on the ground to get the old links off, it's ten times harder fighting the weight of the linkage and the sway bar if you pull the wheel first.

Then once the old ones are off, loose goose fit the new ones, if the sway bar is a little high you can start lifting the corner with a jack and the weight of the linkage and wheel will pull it down and help you line it up, or vice versa.

Once you have it in and the bolts are on kinda loose, hand tight, etc, if you think with your tools and torque wrench pulling the wheel is worth it, go to it. Definitely necessary for torquing the side that's recessed inside the knuckle.

Honestly don't see how you can torque the other side without a lift or a big set of ramps to give you the room to get at it from below. I recommend gorilla tight and chill.

Comparison photo, super easy to get to the zerk fittings if you just full lock the wheels to the opposite side

Now all you need is new UCA's.

Do you like how it drives now?

 

[LawnMM]

Now all you need is new UCA's.

Do you like how it drives now?

Ran out of time before I got the passenger side done, I'll finish it up on Monday

 

[AzScorpion]

 

[Bsenecal]

Yikes, .
Brian

 

[IdahoRanger]

...or Anthony weiner who deserves that.

 

[LawnMM]

Now all you need is new UCA's.

Do you like how it drives now?

Got the other one on before work today. Tried another approach for torque, tried a torque adapter and shorter ratchet instead of the beastly torque wrench that normally handles 85lb ft of torque... also unsuccessful

There really isn't room in there for a torque wrench on the bottom of the end link. My suggestion stands, tighten as tight as you possibly can and call it good. Best measurement I could manage with the torque driver, due to lack of space and leverage was 50+

I believe you can go higher by just muscling it the issue is attaching the equipment to measure it you don't have the room.

Also, you'll have to school me on the UCAs, what's the allure there? Better bushings? Stronger? Do they offer more travel or what?

 

[lariat]

Got the other one on before work today. Tried another approach for torque, tried a torque adapter and shorter ratchet instead of the beastly torque wrench that normally handles 85lb ft of torque... also unsuccessful

There really isn't room in there for a torque wrench on the bottom of the end link. My suggestion stands, tighten as tight as you possibly can and call it good. Best measurement I could manage with the torque driver, due to lack of space and leverage was 50+

I believe you can go higher by just muscling it the issue is attaching the equipment to measure it you don't have the room.

Also, you'll have to school me on the UCAs, what's the allure there? Better bushings? Stronger? Do they offer more travel or what?

Unless you are doing higher, more aggressive off-roading, probably overkill, but since you added those "beefy" control arms, why stop there.

Here's something that may help you decide.

 

[OGMix376]

Unless you are doing higher, more aggressive off-roading, probably overkill, but since you added those "beefy" control arms, why stop there.

Here's something that may help you decide.

“Why stop there” exactly
Build it up to the point of it makes you happy. Send it (keeping it Road “legal” of course .)

You just saved me from an entire day of boredom, thank you.
(Tweaked my back at some point yesterday, so I’m paying for it today.)

Never heard of the tinkerer’s adventure channel. Enjoying it thoroughly. Lots of cool details in the videos.

A ex girlfriend had a nice kitted up FJ (she preferred to have me drive so she could be a passenger princess, she didn’t like how crazy my Evolution at the time was pushing around 440wheel torque) they drive better than taco’s in my opinion… if I was gonna get a Toyota I’d be looking at those gas guzzlers
Well my useless comment of the day has concluded… until next time

 

[OGMix376]

Just got this in from RealTruck.. rapid shipping was very….. rapidly shipped
Gonna put it on tomorrow .

Soft roll up top.

 

[lariat]

“Why stop there” exactly
Build it up to the point of it makes you happy. Send it (keeping it Road “legal” of course .)

You just saved me from an entire day of boredom, thank you.
(Tweaked my back at some point yesterday, so I’m paying for it today.)

Never heard of the tinkerer’s adventure channel. Enjoying it thoroughly. Lots of cool details in the videos.

A ex girlfriend had a nice kitted up FJ (she preferred to have me drive so she could be a passenger princess, she didn’t like how crazy my Evolution at the time was pushing around 440wheel torque) they drive better than taco’s in my opinion… if I was gonna get a Toyota I’d be looking at those gas guzzlers
Well my useless comment of the day has concluded… until next time

I haven't installed any UCA's at this time, but do prefer the drive feel with the updates front swaybars.

 

[subquark]

Just received in email and I'm going to mod town on this windfall! =D

 

[AzScorpion]

Just received in email and I'm going to mod town on this windfall! =D

I can't even think of 1 item you could get for $5.00. Although with your shopping expertise (are you and Annie aren't related?) I'm sure you'll come up with something!