Bedrug HELP!

[Hounddog409]

an

Just so you know.. this is an old thread.. like 6 months old

Then why do your posts show up today if old?

Sponsored

 

[Big Blue]

Ok, does it suppose to be right on that lip or underneath that lip? Can see the half the hole I'm talking about. Just confused on how it goes on. Nothing has been stick on yet. Just trying to figure out that part before I remove all the sticker backing.... I did removed the tie down for now. I'll deal with the holes later. Just want it installed correctly.

I'm my case I tuck the top order that area because that flange and the holes were used for fastening the bulkhead filler for my tonneau cover.

 

[BlackRanger01]

I'm my case I tuck the top order that area because that flange and the holes were used for fastening the bulkhead filler for my tonneau cover.

So you're saying the top of the bed liner would meet at the bottom of that area in this edited picture where the red lines are? Not attach it like the other picture where I was holding it covering half the hole? Just want to be clear.

 

[BlackRanger01]

Then why do your posts show up today if old?

Ah ignore me, sorry.

 

[Big Blue]

So you're saying the top of the bed liner would meet at the bottom of that area in this edited picture where the red lines are? Not attach it like the other picture where I was holding it covering half the hole? Just want to be clear.

E

Yes it would be tucked under where you red line is . I seem to remember there is a angled surface from your line down and if you push the bedrug tight to the bed it should end at about where you line is with the tape on the bevel. At least that's how it worked out for me on my 2019.

 

[BlackRanger01]

Yes it would be tucked under where you red line is . I seem to remember there is a angled surface from your line down and if you push the bedrug tight to the bed it should end at about where you line is with the tape on the bevel. At least that's how it worked out for me on my 2019.

Thanks - it feels like its gonna be a tight fit. I'll give it a go tomorrow. Not sure how it'd work with the sticker being right there. Currently sitting in garage with it like that in picture heh.

 

[BlackRanger01]

Anyone else got any suggestions? If i could get a close up picture of the area I am talking about, it would be awesome.. if not no problem! TYIA!

Also how did you make the holes for the tie down? Just poke it with some sharp object?

EDIT: I know i sound like a newbie but I tend to fuck up and just want to be sure I am doing it right.

 

[BlackRanger01]

@AzScorpion - I will install the new damper very soon! Can't wait.

 

[Tri-J]

This was install day, several months ago. I put the front up near the top of the bed. On the tie downs-you can cut a slit and poke the tie downs thru or you can remove them, poke two holes for each, and reinstall them over the bedrug.

 

[BlackRanger01]

This was install day, several months ago. I put the front up near the top of the bed. On the tie downs-you can cut a slit and poke the tie downs thru or you can remove them, poke two holes for each, and reinstall them over the bedrug.

I originally thought i'd attach like that but i just did it on the front and I am pleased with result. Next post is a picture. And thank you for posting your picture!!

 

[BlackRanger01]

Yes i did this at 11PM EST .... lol neighbors must think im nuts. I am in garage with door open and truck half way out...

What I did is, pull a couple inch of backing off the tape, stuck it on the corner and push in the rest of the edge in and pull tape and press it onto slanted side, and keep pulling tape and pressing the edge. worked out great.

Now I gotta go back out and do the sides.... and tailgate.. ugh this is like a 10 hours job to me... lol. I"m so anal about this.

 

[BlackRanger01]

I removed the four tie down anchors for now. Will make holes for them later. Hope I can find the holes later.

 

[BlackRanger01]

Completed.... two small issue.. one is the passenger liner wall near the front keep popping out, I can press it in and it's perfect but it kept popping out.. know any fix except putting double sided velcros on that side?

Other is the velcro can be seen at rear of the truck. No biggie, I am very happy the way it turns out.

 

[subquark]

Came out great.
Sorry about yesterday, but my frustration level was thru the roof. How could bedrug.com not know wth was going on with that damn zipper?
It's never coming out, so instead of cutting slits in it, I just poked holes and ran the bolts thru it. Gives it more if a "finished" look.

I also bolted the tie downs right through the BedRug. And I also found it frustrating to get in. Not hard, just cumbersome and a big PIA!

But I like it and am glad to have it, seems to work great so far.

 

[subquark]

Ok, does it suppose to be right on that lip or underneath that lip? Can see the half the hole I'm talking about. Just confused on how it goes on. Nothing has been stick on yet. Just trying to figure out that part before I remove all the sticker backing.... I did removed the tie down for now. I'll deal with the holes later. Just want it installed correctly.

I pushed that tape onto the sloped area just under the top. The thing has enough stiffness that I don't think you can really install it wrong. I do wish it would less "baggy" but once in, it looks great!

I used an awl on a pocket knife to find the tie down holes and just screwed them on through the BedRug.

Ain't know way that the BedRug will ever fly out! That said, I know some of the tape is barely sticking on to some spots but it's in there.

Sponsored