Sponsored

Amp Power Steps install cost.

tgRanger

Well-Known Member
First Name
Tony
Joined
May 13, 2019
Threads
11
Messages
497
Reaction score
1,452
Location
NJ
Vehicle(s)
2004 Ford F-150 Lariat, 1988 Mustang GT, 2013 Toyota Highlander Limited
Vehicle Showcase
1
Hello everyone. To all that purchased these Amp steps and had them professionally installed may I ask what you paid for installation?

I bought a set from Real Trucks with the intention of installing them myself but I have a bad hip and decided to maybe get them installed and not risk further injury.

I was quoted $620 from one shop and think that was a bit much. What have you all paid.

Anyone on NJ area able to install them for me? ? Thanks in advance
Sponsored

 

Rence

Well-Known Member
First Name
Laurence
Joined
Dec 5, 2019
Threads
2
Messages
50
Reaction score
115
Location
Insanity Central
Vehicle(s)
2019 Ranger XLT FX4
To be honest I don’t think the price is really that unreasonable for a qualified shop, it’s a four hour install minimum, took me 6 hours the first day including the LED lights ,The next day was 1 1/2 hour for the bypass switch. Check around but make sure they are qualified.
 

Muscleford

Well-Known Member
First Name
George
Joined
Mar 24, 2021
Threads
90
Messages
758
Reaction score
1,491
Location
Ohio north coast
Vehicle(s)
21 Ranger Lariat, 84 & 85 Merc Capri 5.0, 23 Escape
Occupation
Retired CFO
My son and I installed mine took about 4 1/2 to 5 hours with no by-pass switch.
 

HeatXfer

Well-Known Member
First Name
Chris
Joined
Jan 15, 2024
Threads
6
Messages
279
Reaction score
689
Location
Nor Cal
Vehicle(s)
2019 Ford Ranger XLT SuperCrew
Occupation
Retired Pipefitter & commercial HVACR Tech
Conservatively, anywhere from $100 to $150 an hour. If that shop only does repairs and has never installed something like the powered step, $650 sounds about right for the time they'll spend.
 

TJC

Well-Known Member
First Name
Tony
Joined
Aug 28, 2020
Threads
45
Messages
3,930
Reaction score
9,849
Location
North Carolina
Vehicle(s)
93 Miata, 05 Ranger 4x4, 20 Ranger 4x4, 23 CX-5
These guys are on target. I am 68 and it took me ~6 hours. I notice that it gets harder each year to lay on that cold concrete.

I did use different LED lights, and cheated by using very strong magnets to place them. I didn't like the idea of drilling mounting or wiring holes in the bottom of the truck.

I did drill one hole to route the wiring into the drivers footwell per the instructions, but used Rustoleum primer to cover the bare metal, then coated the hole mating surfaces with silicone before installing a silicone doughnut gasket on the wire and mounting it in the hole. Figured that would protect the bare metal from the elements.

I absolutely love the steps. One of my favorite additions to the truck.

Oh, no bypass switch either.
 


OP
OP
tgRanger

tgRanger

Well-Known Member
First Name
Tony
Joined
May 13, 2019
Threads
11
Messages
497
Reaction score
1,452
Location
NJ
Vehicle(s)
2004 Ford F-150 Lariat, 1988 Mustang GT, 2013 Toyota Highlander Limited
Vehicle Showcase
1
Thank you for the replies everyone. Looks like I'm going to bite the bullet and get them professionally installed.

The shop that I chose came recommended from Real Trucks site as an authorized dealer and installer. There was another one that I called and they said they only install the ones they sell. So I was out of luck there. This one did question me as well making sure I purchased them from RT’s, something about being able to honor the warranty.

Plus from what I’ve been reading these are hit or miss on the install, with some having issues. So I’ll leave it to the pros and get an install warranty so they can deal with it if I have any problems down the road. And I save my hip and pain to boot.
Sponsored

 
 








Top