What did you do to your Ranger today?

[LegacyRanger]

I installed my new tires! 265/70/17 Falken Wildpeak AT3W on my stock wheels with no spacers. I seriously love the upgrade! I also have the @Fordrangerlifts.com 2.5" level kit and Shrockworks sliders installed.

What are are your ground to wheelwell measurements? I'm having a hard time deciding between fordrangerlifts.com 2.5 and 3.0 kits? Yours looks very level with the 2.5 kit.

Sponsored

 

[Manny]

Added some flair to the interior...

how did you do the steering wheel emblem? can you provide link

 

[TylerV76]

Swapped out the halogen low beams and fogs to LED’s. Will start looking at LED’s for the high beams soon.

Also set daytime running lights to parking lights only.

 

[Scottopia]

how did you do the steering wheel emblem? can you provide link

It is just a decal, simple overlay. Picked it up on Etsy. Seems well made.

Red/Black Ford Emblem overlay

 

[JAKE2.3]

Got my rewards points in less than a week. Stopped by the local ford/gm dealer to order some accessories. Went through all the hoops, and apparently they’ve never done it since I had to explain how the process goes. Finally got a work order and took it over to parts. Kid there ordered me the parts and said he’d figure it out one way or another. Guess I’ll wait a couple days for a call to see if they came in. I’m not sure why the process has to be so difficult. He said it was much simpler for gm rewards.

 

[Julio]

for the millionth time, I master reset the Sync3
i dont think it fixed anything again

Same, getting old fast

 

[BDoc]

Finally had decent enough weather (for the day and the forecast) to put the side molding on. After looking at the picture, it appears I may be off just a hair front to back. Good thing I'm not OCD or that would piss me off more than it already does.

 

[Capt'n Awesome]

Reworked the tailgate badging.

 

[PNW_Ranger87]

What are are your ground to wheelwell measurements? I'm having a hard time deciding between fordrangerlifts.com 2.5 and 3.0 kits? Yours looks very level with the 2.5 kit.

I haven't measured them yet but I already knew I wanted to go with the 2.5" because if anything I wanted it to be raked a tad forward. Especially when I start using the bed for hauling anything or when I start towing. I'm eventually going to go with an adjustable coil over setup but this definitely meets my aesthetic needs for now!

 

[PNW_Ranger87]

What are are your ground to wheelwell measurements? I'm having a hard time deciding between fordrangerlifts.com 2.5 and 3.0 kits? Yours looks very level with the 2.5 kit.

Ok I measured it. 38"F and 39"R. That's directly above the center of the wheel but I'm not sure if that's the highest actual point of the fender. That's also with 265/70/17 tires. I think it sits perfect with the 2.5" level. ?

 

[LegacyRanger]

Ok I measured it. 38"F and 39"R. That's directly above the center of the wheel but I'm not sure if that's the highest actual point of the fender. That's also with 265/70/17 tires. I think it sits perfect with the 2.5" level. ?

Great! Think I’m going with this set up! Appreciate the help!

 

[LegacyRanger]

Got my new exhaust tip put on. Decided that I didn’t like the sound of any of the cat back systems with the 4 banger so just went with the esthetic and cheaper route. Amazon find for less than $40.

 

[Onlyone]

Changed the oil and rotated the tires.

 

[Arch Stanton]

SVC 2" Leveling Collars, Michelin LTX A/T2 265/70 17's and Steelcraft 4X Series Nerf Bars.

 

[moredneck]

Which level kit did you go with? Looks great!

RC 2.5”

Sponsored