What did you do to your Ranger today?

[TylerV76]

Well since I took a detour on the way home last night when I saw an intriguing dirt rode covered in mud, this morning I decided it was time for the first real bath at home.

In case anyone wonders what its like washing a car while its 21 degrees outside, its substantially worse than it sounds.

Decided to also change the splash screen on the stereo and fine tune my speedo for the new tires in forscan.

Trying to decide now if I do the Sync 3.4 upgrade or hold out for an official release.

Sponsored

 

[AzScorpion]

Well since I took a detour on the way home last night when I saw an intriguing dirt rode covered in mud, this morning I decided it was time for the first real bath at home.

In case anyone wonders what its like washing a car while its 21 degrees outside, its substantially worse than it sounds.

Decided to also change the splash screen on the stereo and fine tune my speedo for the new tires in forscan.

Trying to decide now if I do the Sync 3.4 upgrade or hold out for an official release.

Get yourself a pair of neoprene diving gloves with a high cuff. I used to wash my trucks all winter long when I lived back east and these were a life saver for your hands.

 

[jerrywin]

Installed TPMS. Awaiting tire delivery.

went with the 4pack TPMS42 for 59.
https://www.ebay.com/itm/4pcs-New-F...480?_trksid=p2349526.m4383.l4275.c10#viTabs_0
And
Got Schrader metal stems (to go with the aluminum winter wheels I got).
https://www.amazon.com/gp/product/B007NK2L66/ref=ppx_od_dt_b_asin_title_s00?ie=UTF8&psc=1

went with Nankang AT-5 CONQUEROR A/T (actually got them at Discount Tire Direct, but could not find link)
https://www.discounttire.com/buy-tires/nankang-tire-at-5-conqueror-a-t/p/34735

 

[Kaladin]

Installed my Wet Okole seat covers. Just in time for rain.

 

[Kaladin]

Also installed aluminum ignition bezel I made yesterday.

 

[BDoc]

Installed the tailgate damper

 

[Snorebaby]

Added my Wild Rhino decal. It's a Kansas based group of friends that happen to ride Goldwings. It started after the Wild Hogs movie came out. I have been a "member" for years but finally got my decal. Had the patch since I was "inducted" into the group in 2010.

 

[HighCaliberMitch]

I did this:

But I'm not enamored with the outcome.

The A and the E are the only two that didn't seem to need to stretch into the form.

Is there some special way I'm missing; I followed the online instructions.

 

[Dmax]

Installed Bushwacker Side Rails for the doors. More protection for the paint.

 

[jlmotox]

My Ranger made some friends today, SoCal Hungry valley meet up. Great time great people!

 

[P. A. Schilke]

I did this:

But I'm not enamored with the outcome.

The A and the E are the only two that didn't seem to need to stretch into the form.

Is there some special way I'm missing; I followed the online instructions.

Hi Antonio,

Yeah...my fear as well...will wait until someone like eyecatcher creates plastic colored lettering for this application... So far nothing I can find on line. That said. I would bet most folks will not notice and think it is very cool. Don't sweat the petty stuff and don't pet the sweaty stuff, eh?

Best,
Phil Schilke
Ranger Vehicle Engineering
Ford Motor Co, Retired

 

[FULLSCALE]

I finally gave my truck a vacuum, interior wipe and floor mat clean followed by an exterior wash. It was just above freezing today and the wash was long overdue. The only photo I took is through the window while waiting to pick up pizza!

 

[Nutty 5.0]

I finally gave my truck a vacuum, interior wipe and floor mat clean followed by an exterior wash. It was just above freezing today and the wash was long overdue. The only photo I took is through the window while waiting to pick up pizza!

Jealous; miss being able to have pizza!! Hope it was great!

 

[FULLSCALE]

Jealous; miss being able to have pizza!! Hope it was great!

It sure was!

 

[Nutty 5.0]

Actually hauled some stuff. In laws are down sizing and selling their house around here as they live in Albany area in their new home for a few years now. They gave me their rock candy Barrel from Brooklyn and an old wagon wheel. MX4 cover did great as did my buddy’s 3D printed “Much Improved” support rod holders.

No, the wheel isn’t a full size spare lol!

Sponsored