Nollie's Reggie Build

OP
OP
Nollie

Nollie

Well-Known Member
First Name
Dan
Joined
Nov 20, 2020
Threads
3
Messages
98
Reaction score
425
Location
Washington
Vehicle(s)
2020 Ford Ranger XLT, 2020 Subaru Impreza Sport, 1996 Porsche Carrera 4S, 1987 Toyota Pickup
Occupation
Red team analyst
Vehicle Showcase
1
OP
OP
Nollie

Nollie

Well-Known Member
First Name
Dan
Joined
Nov 20, 2020
Threads
3
Messages
98
Reaction score
425
Location
Washington
Vehicle(s)
2020 Ford Ranger XLT, 2020 Subaru Impreza Sport, 1996 Porsche Carrera 4S, 1987 Toyota Pickup
Occupation
Red team analyst
Vehicle Showcase
1
CB Install

Wanted to get a CB radio installed for primarily off-road use. My intent is to have it mounted on the Built right dash tray mount. Major parts:
20210911_205016165_iOS.jpg

Dropped the headliner a little bit, using the video on the brake controller install as a guide (pretty simple, just pull down along the edge of the headliner until the clip pops out.


20210911_210457880_iOS.jpg
'
Marked the left side coax so when I get the wires to the front I know which is which.

20210911_211132224_iOS.jpg

Pulled the 3rd brake light off

20210911_211447705_iOS.jpg

With the light disconnected, it was pretty easy to push the tape and get the coax into the cabin. It was a warm day so the adhesive didn't give me much resistance.

20210911_211509999_iOS.jpg

I pulled the coax out the door and into the bed so I could feed it through without any helpers.

20210911_212203688_iOS.jpg

That's when I noticed my first... hurdle. The chase rack and the antenna mount don't play nicely together :mad:. I took off the center beam to figure something out. Most likely it'll involve some cutting of the chase rack. Eventually I'm moving to a bed rack anyway so I might just take it off.

20210911_213226271_iOS.jpg

Installed pretty easy. I lined it up and decided to add the additional brackets they send.

20210911_213324771_iOS.jpg

Drill 4 holes, slide the brackets in and bolt them down

20210911_214130370_iOS.jpg

About to button up

20210911_214850732_iOS.jpg

20210911_215227208_iOS.jpg

This is the 2' firestik, 3' is on order

20210911_220401735_iOS.jpg

popped off the door sills

20210911_220905439_iOS.jpg

dropped the glovebox

20210911_222139010_iOS.jpg

Unbolted the seat, but couldn't get the wires disconnected. I didn't have enough wire to run the coax from the mount to the top of the dash along the edge so I went under the carpet from the back to the front console.

20210912_010115025_iOS.jpg

So close ??? . I have an extension on order and I just have running the power for the CB, adding a quick disconnect so I can take the CB off the dash, and tuning the antenna.

More to come once parts are here :D
 
OP
OP
Nollie

Nollie

Well-Known Member
First Name
Dan
Joined
Nov 20, 2020
Threads
3
Messages
98
Reaction score
425
Location
Washington
Vehicle(s)
2020 Ford Ranger XLT, 2020 Subaru Impreza Sport, 1996 Porsche Carrera 4S, 1987 Toyota Pickup
Occupation
Red team analyst
Vehicle Showcase
1
Fixed one of the challenges today with a bit of angle grinder action. Looks decent enough until I switch to a bed rack system :)

07BB3AC3-5AAA-4352-A871-B6D6FC0F9F92.jpeg

59A2A1A4-364D-49F1-A0E2-B80FB37E1F8B.jpeg
 
  • Like
Reactions: Doc
OP
OP
Nollie

Nollie

Well-Known Member
First Name
Dan
Joined
Nov 20, 2020
Threads
3
Messages
98
Reaction score
425
Location
Washington
Vehicle(s)
2020 Ford Ranger XLT, 2020 Subaru Impreza Sport, 1996 Porsche Carrera 4S, 1987 Toyota Pickup
Occupation
Red team analyst
Vehicle Showcase
1
Rest of the parts came in today so I could finish.
20210914_214534462_iOS.jpg

Bought some 16g quick disconnect plugs and a coax extension (1m). I figured with the quick disconnects I can remove the CB and if something else uses 12v I can use another plug end and be up and running quickly.

20210914_215145032_iOS.jpg

Also decided to try these heat shrink no-iron solder connectors. They're not too bad, not as nice looking of a finished product as just solder and heat shrink.


20210913_222250377_iOS.jpg

Using the grommet that's on the passenger side accessible behind the glovebox. This is the engine bay passenger back corner. You can see the wire going into the grommet and electrical taped down. I removed the electrical tape and used a coat hanger to push through the grommet to the other side.

20210913_232108164_iOS.jpg

Once on the other side I taped the wire to the coat hanger and had my wife pull the hanger back out while I pushed the wire. The first time the wire didn't stay on the hanger... I changed to a small hook on both the wire and the hanger with tape and that pulled through no problem.

20210914_013933396_iOS.jpg

Added wire loom and taped everything back up. I ran the wires up to the front and across instead of along the back. It was easier to place the wire, and I already had some from other projects so it looked reasonable.

20210914_011641086_iOS.jpg

Soldered on two battery connectors (hooked up later)


20210914_230750241_iOS.jpg

Cut and soldered on the quick disconnect. See what I mean... not as clean but it'll do the job and I didn't have to worry about soldering in the truck.

20210915_022840567_iOS.jpg

Moved the ram mount for the phone, added the bracket for the CB and buttoned it all up.

Overall happy for now. I'm a little worried about the weight on the tray in the case of an accident; might look at bolting the tray to the underlying plastic support. Should be good enough for my trip this weekend :D
 

UnregistredHypercam2

Well-Known Member
First Name
Jon
Joined
Aug 15, 2021
Threads
22
Messages
278
Reaction score
890
Location
Denver, Colorado
Vehicle(s)
1997 Toyota Land Cruiser VX Limited
Occupation
Cybersecurity
Nice to see another infosec guy in the Ranger world, although I sit on the blue team side of the house. Excellent build!
 
  • Like
Reactions: Doc


OP
OP
Nollie

Nollie

Well-Known Member
First Name
Dan
Joined
Nov 20, 2020
Threads
3
Messages
98
Reaction score
425
Location
Washington
Vehicle(s)
2020 Ford Ranger XLT, 2020 Subaru Impreza Sport, 1996 Porsche Carrera 4S, 1987 Toyota Pickup
Occupation
Red team analyst
Vehicle Showcase
1
Nice to see another infosec guy in the Ranger world, although I sit on the blue team side of the house. Excellent build!
Thanks! I do about 75% red and 25% threat hunting / blue. It's a great mix, we do a lot of purple to keep our alerting up to date. Never a dull day :D
 

UnregistredHypercam2

Well-Known Member
First Name
Jon
Joined
Aug 15, 2021
Threads
22
Messages
278
Reaction score
890
Location
Denver, Colorado
Vehicle(s)
1997 Toyota Land Cruiser VX Limited
Occupation
Cybersecurity
Thanks! I do about 75% red and 25% threat hunting / blue. It's a great mix, we do a lot of purple to keep our alerting up to date. Never a dull day :D
awesome, I live in the IR world so more in line with hunting and some purple to taste
 
OP
OP
Nollie

Nollie

Well-Known Member
First Name
Dan
Joined
Nov 20, 2020
Threads
3
Messages
98
Reaction score
425
Location
Washington
Vehicle(s)
2020 Ford Ranger XLT, 2020 Subaru Impreza Sport, 1996 Porsche Carrera 4S, 1987 Toyota Pickup
Occupation
Red team analyst
Vehicle Showcase
1
Trying to adjust my antenna for better SWR. I started with a 2’ Firestik and it took everything I could to get to 2.5 on channel’s 1 and 40. Before took g too much diagnostics, I switched to a 3’ and I got it to 1.5 on channel 1 and 40. I’m happy with the 3’ but it’d be nice to have something shorter for on-road.

Any knowledgeable CB guys have ideas? Maybe the antenna is bad? @WxNerd2015 did you have any SWR issues?

3126ABF6-4C8F-4041-928F-8C09B1953E24.jpeg
 
  • Like
Reactions: Doc

WxNerd2015

Well-Known Member
First Name
Trevor
Joined
Oct 17, 2018
Threads
9
Messages
296
Reaction score
1,032
Location
Gregory, Michigan
Vehicle(s)
2019 Ranger, 2011 Wrangler, 2017 Escape
Occupation
Applications Engineer
Vehicle Showcase
1
Trying to adjust my antenna for better SWR. I started with a 2’ Firestik and it took everything I could to get to 2.5 on channel’s 1 and 40. Before took g too much diagnostics, I switched to a 3’ and I got it to 1.5 on channel 1 and 40. I’m happy with the 3’ but it’d be nice to have something shorter for on-road.

Any knowledgeable CB guys have ideas? Maybe the antenna is bad? @WxNerd2015 did you have any SWR issues?

3126ABF6-4C8F-4041-928F-8C09B1953E24.jpeg
Well, for me, my stinger CB antenna definitely has a much better SWR than my short antenna, as the ideal CB length is 102", but I was able to get my JBC800 (8" antenna) down to about a 2.0 SWR reading at 1 OR 40, and then the rest settled about 1.4-1.8 on the SWR readings. I could not bring both ends of the spectrum down, but I could bring one end down, and the channels I use in the middle were all more than acceptable reading. The stinger is about 1.2-1.5 across the entire range. I use the JBC800 on a daily basis mostly for receiving, but when I know I will be transmitting more, I switch over to the stinger.
Sponsored

 
 



Top