woodworker
Well-Known Member
I’m looking into this right now. I’m not a big fan of modifications but I don’t want to create more problems than I have right now if they’re going to install something that is faulty right out of the box.
Sponsored
Sponsored
Driveshaft center support bearing
- Thread starter Old and new
- Start date
- Watchers 8
woodworker
Well-Known Member
Just sent email to Tom Woods.
Chris M
Well-Known Member
- First Name
- Chris
- Joined
- Jun 11, 2020
- Threads
- 21
- Messages
- 4,501
- Reaction score
- 19,814
- Location
- Surprise, AZ
- Vehicle(s)
- 2021 Ranger XLT Sport 4X4
- Occupation
- Security Supervisor
If I were going to have to do a driveshaft replace on my dime, I would get a one piece from them. You hear nothing but good things about them from folks here that have them.
TJC
Well-Known Member
- First Name
- Tony
- Joined
- Aug 28, 2020
- Threads
- 45
- Messages
- 3,947
- Reaction score
- 9,919
- Location
- North Carolina
- Vehicle(s)
- 93 Miata, 05 Ranger 4x4, 20 Ranger 4x4, 23 CX-5
The TW driveshaft is hands down the best change I made to my Ranger. I am convinced that it takes stress off the drive train (including the transmission). And I like my Eibach's and my Amp Power Steps...
... and an honorable mention to the tailgate damper, just because Dave is a nice guy!
... and an honorable mention to the tailgate damper, just because Dave is a nice guy!
Titchadesh
Well-Known Member
Agreed. On top of getting rid of the highway vibrations, it felt like my truck got a brand new transmission as well. There is just way too much play in that two-piece from day one, and it only gets worse in time as the center bearing deteriorates.
Having installed mine 2 months ago--to me this is a no-brainer, but I understand I'm not the one who will have to get under the truck! If you do end up going for the TW, I'm sure there are plenty here who can give install advice, myself included
TJC
Well-Known Member
- First Name
- Tony
- Joined
- Aug 28, 2020
- Threads
- 45
- Messages
- 3,947
- Reaction score
- 9,919
- Location
- North Carolina
- Vehicle(s)
- 93 Miata, 05 Ranger 4x4, 20 Ranger 4x4, 23 CX-5
I was 67 when I installed it. It is pretty straight forward process... I had no trouble installing it. Took me about 90 minutes to remove and replace it. It's been on my truck for quite a while now... Since early Oct 2022. I grease the splines annually whether they need it or not. 5 minute job.
Titchadesh
Well-Known Member
The purchase page has instructions on how to do this: https://4xshaft.com/collections/ford-products/products/5th-generation-ford-ranger-rear-drive-shaft but essentially you crawl under the truck with measuring tape and measure from flange to flange. When I measured, it was 66 3/4" from end to end, and a measurement in that ballpark range is normal according to reports here on the forum. Here is the image they give you to reference the measurement:
lou5560
Well-Known Member
- First Name
- Louis
- Joined
- Aug 16, 2021
- Threads
- 2
- Messages
- 106
- Reaction score
- 234
- Location
- New Jersey
- Vehicle(s)
- 2019 Ford Ranger XLT FX4 Off Road
- Vehicle Showcase
- 1
Thank You so much. I have a 2019 Supercrew FX4 Off RoadThe purchase page has instructions on how to do this: https://4xshaft.com/collections/ford-products/products/5th-generation-ford-ranger-rear-drive-shaft but essentially you crawl under the truck with measuring tape and measure from flange to flange. When I measured, it was 66 3/4" from end to end, and a measurement in that ballpark range is normal according to reports here on the forum. Here is the image they give you to reference the measurement:
Sponsored
