2019 Ford Ranger OEM Splash Guards

[rooster]

My mudflaps arrived but the front hardware bag had no clips, despite saying qty 4 clips right on the bag.

As I took out the drill I heard a female voice from a distance ... "WHAT are you doing to your new truck??" ... 30 minutes later they were on nice and tight.

Might track down some clips but the screws seem sufficient.

Sponsored

 

[Floyd]

My mudflaps arrived but the front hardware bag had no clips, despite saying qty 4 clips right on the bag.

As I took out the drill I heard a female voice from a distance ... "WHAT are you doing to your new truck??" ... 30 minutes later they were on nice and tight.

Might track down some clips but the screws seem sufficient.

I just installed mine front and back, fortunately I got my hardware kits.
It only uses screws put back where they came out at the bottom.
The rest are push pins and clips.
You only drill through plastic, so screws won't hold long term.
I suggest that you get the hardware kits right away, or remove the splash guards until you do.

Did you get the instruction sheets?
My hardware kits were in separate bags inside the larger bag which contained the guards.

 

[RCMUSTANG]

Finally got my buddy at the dealer to order me a set at employee cost. I'm a fan of molded factory style.

 

[MT19RANGER]

Finally got my buddy at the dealer to order me a set at employee cost. I'm a fan of molded factory style.

I like mine and that's why I ordered them during the build.

 

[RCMUSTANG]

I like mine and that's why I ordered them during the build.

Eh, I knew it would be cheaper to install them myself. I'm ok with spending the savings on other upgrades.

 

[Msfitoy]

Installation of my front set took about 10 minutes...my rear set is finally arriving today...might run home and slap them on during lunch

 

[rooster]

I just installed mine front and back, fortunately I got my hardware kits.
It only uses screws put back where they came out at the bottom.
The rest are push pins and clips.
You only drill through plastic, so screws won't hold long term.
I suggest that you get the hardware kits right away, or remove the splash guards until you do.

Did you get the instruction sheets?
My hardware kits were in separate bags inside the larger bag which contained the guards.

The front the hardware bag only included push pins and two new screws. Printed directly in that bag it said qty 4 with the clip part number! It was sealed too. So the fronts have the one screw and push pins, I’ll see if they will send me some of the missing clips.

The rears are clipped, push pinned and screwed.

 

[Floyd]

The front the hardware bag only included push pins and two new screws. Printed directly in that bag it said qty 4 with the clip part number! It was sealed too. So the fronts have the one screw and push pins, I’ll see if they will send me some of the missing clips.

The rears are clipped, push pinned and screwed.

On the front,the one screw for each side is designed to replace the one which was removed.
I decided to use the original because the flange on it is bigger which I thought would better support the plastic.
There are marks where the two clips are to be installed. I hope they will supply the clips, if not maybe a short aluminum pop rivet with a large flange could be substituted.
Look around again though, on mine the four clips were stuck together forming one little chunk, maybe it fell out and bounced under the tool box or something. Good luck.

 

[Cape Cruiser]

Mine came with the wrong push pins. Directions say drill 1/4 inch hole but my push pins where 5/16 and I didnt want to drill that large of a hole near the edge of the plastic. I had 1/4 inch push pins in stock so I used mine. They fit very nice!

 

[Cape Cruiser]

Mine were $92.00 on ebay

 

[Floyd]

Ford list price is $49 front set and $49 back set, plus tax of course.
My dealer sold them to me at cost as a consideration for buying the truck.

 

[Msfitoy]

Finally got my rear set to match the front...first Ebayer never responded and then without a word canceled my order...got the first negative feedback from me...second Ebayer shipped them in 3 days....took 10 minutes to install...

 

[Jeffrey]

I had to remove front crash bars for rim and tires installation. Do you think u clip will still fit?

 

[Floyd]

Oddly enough, my truck did not come with that screw/pushpin in the wheel well trim which is shown in the video.

Sponsored