Search results

Can this be installed with the hard, black plastic Ford drop in bedliner WITHOUT having to cut holes in it or cut pieces of it off??

Mine was built May 2022 so I only have to do regular level worrying or what?

Googled those bulbs & it looks exactly like what was in there. The wires coming of the inside end of the blade connectors is skinny & flimsy, 1 seems to be missing completely, & the black capsule shaped piece of plastic that the connectors pass through is not anchored into the housing in any...

Which of these are short enough that you can get the cover back on the driver's side low beam? XLT Tremor. The front edge of the inner fender apron is very close to the back of the bulb. Tight space to get the cover back on & the outer part of it is slanted. Only the center part of the cover has...

Check if your auto up & down driver's window still works. And the safety reversal for the window. It has to be reset after battery disconnect.

Can't get to vent because of the carpet overlying it.

How did you get the carpet off the back wall of the cab? I couldn't see an easy way. Being held on by plastic trim pieces below back window.

I Google searched the image and there are bunch of them for sale on eBay & Facebook for ~$5-$20. I just wish car dealers would remove crap like this when they sell the car. It's not factory, I didn't ask for it, I didn't consent to it, & it serves no useful purpose for me.

Anyway, truck seems to run & drive fine without it. Any ideas if it will screw up Ford Pass app or any other software/electronic stuff?

Nope, purchased CPO used from Sam Galloway Ford in Fort Myers, financed through AAA Banking car loan. Have since paid that off by balance transferring to 0% Bank of America credit card. It is odd the the FoMoCo thingie that was inline with the back of the OBD port & my white ziptie are gone (...

I took my truck in to the dealer about 6-8 wks ago for what turned out to be rodent damage to the passenger airbag wiring harness. Prior to that I had noticed a FoMoCo electronic doodad dangling loosley behind & above the OBD port. It was wired inline with the port. It was clearly an add on & I...

I am using the Fresh Cab Rodent Repellent & Spider Repellent.

Further Adventures in Rodent Proofing After sustaining $543 worth of damage to the passenger side airbag wiring, I went on a rodent proofing mission. You will need a Lisle Tools 54150 wiper puller if you have any hope of ever getting the wipers off. Why do I need to take the wipers off you...

Mission accomplished. Would not have budged without this. There are very fine splines on the shaft & inside the wiper arm hole. Stuck super tight.

Already tried that. Hence the frustration & post. Now I have to buy a Lisle Tools 54150 wiper arm puller that I will almost certainly never use again in my life to address one Ford screw up to address the bigger Ford screw up of the rodent access holes stamped in the firewall. Which so far have...

I need to get my wipers off to get the cowl cover off to rodent proof the holes in the firewall. Wipers will not budge & I do not have a puller. Have tried prying under the base with 2 screwdrivers & a 21mm open end wrench. No go. Any ideas??

This was my first time draining with it. Did not know what flow rate would be like & didn't want to overflow the funnel that screws to my oil drain container. My drain hose also has a permanent hairpin bend in it from being folded in the bag requiring me to hold it to aim it correctly. Did not...

I just did my first oil change with ValvoMax installed. Piece of cake. I had to use some slip joint pliers to get the cap off but draining was tidy. Slower than with the factory drain plug removed but you just have to hold the drain hose over the funnel of your drain pan for 5-7 minutes or so...

Well, the nut was backed off several turns from actually contacting anything. Nowhere near even finger tight. I bottomed out a 10mm deep socket tightening it and the handle still didn't feel very taut when pulling up. I ended up using a 10mm flex head flare nut wrench to get it satisfactorily...

Check out Thule, Saris, Kuat, and Hollywood Racks. You definitely want one rated for ebike weights that pivots downward to make for easier loading and getting out of the way of the tail gate.