I had bought the Adams Premium Foam Cannon and Mega Foam for up north. One fill lasts three washes and I rarely have to do anything but dry afterwards. If I feel like I need to put a mitt to the car with a full wash or to avoid water spots I’ll make a batch of waterless wash using Wolfgang...
I don’t see this happening here in the states. Localities generate far too much revenue through moving violations to give that up. In smaller communities the revenue can be a significant portion of income that could only be made up by higher taxes. It’s easier for localities to raise fines...
maybe sticky is the wrong word here. Slightly tacky may be better. Compared to an old school carnuba and that hard shell where a rag when finished felt like your hand across wet ice, 303 has a slight grip to a rag. Wolfgang achieves that feel. Now I can’t complain about performance. Whether a...
Gave the poor girl some much needed attention.
Broke out the upholstery cleaner and gave the interior a deep clean. Pup has taken to chasing geese through the marsh and thoroughly stunk up the joint. Really impressed with the Carhartt seat covers. Cleaned up like new and they sure do take a...
I’ve tried Duluth Trading but have since gone back to good ole fashioned Hanes.
since I’m getting older and gravity is wearing in I am looking for a good supplier with sway control.
My favorite thing is the gift of a sticker on a board of walnut warning me that said walnut can cause cancer. Pretty soon you guys will have stickers on live trees also.
Ahhh the ole political bait and switch. We are gonna give some of you a grand in inflation relief. But we are raising gas taxes. So everything reliant on gas now goes up to cover the tax increase resulting in further inflation and a negative offset.
Keep it up California! Just increasing...
I couldn’t tow my CAT 259D3 even with a trailer. At 8950lbs I’d be slightly overweight.
A friend of mine up here has a 299D3 and tows with a 16,000lbs gooseneck. Towing that kind of weight with a bumper pull is just a nightmare.
Gave the poor girl a bath now that it looks like we may get some sunshine for at least a week. Been a strange start of the summer with all the rain and cooler weather, although I'm not complaining about 60 degree days in June.
Also made a simple nesting rack for hauling sheet goods out of...
I haven't tested yet. Only drove around 3 miles a day back in Phoenix so not really a good test. I did bring it up north with me where I drive a lot further so can get a better test. I just need to get things setup with Forscan and log some results.
Back in Phoenix my normal routine is horrible on gas mileage. Three mile round trip for coffee and pup cups in the morning is not the best gauge for fuel mileage, as I would only average just under 18 mpg.
But reset the trip meter for the trip to Idaho and with a daily routine of 28 mile...
Another pro damper reason. Over time your skin will become rubbery and splinters bounce right off.
In all seriousness….so true! I always bring gloves now or borrow a pair a few aisles over.
@OFC Ranger I’ve seen it done like that. But to hide the rough edge of the cut they typically dado in a 1/4” ledge top and bottom slightly wider than the thickness of the door to form a ledge. So if you have a 1 3/4” door cut a piece of wood 2” x 3/8” x length of door. Dado along the length...
Nice work! I’ve got A bunch of cedar that has to come out that is 3-6” dbh that my uncle wants some for turning along with some serviceberry . Always wanted to get into it but never found the extra time.
You could alway take on a side hustle. Met a Canadian national treasure this morning. Old dude, easily 80+, full of spit and vinegar that dropped “f “ the government in every other breath. He runs a 12’ trailer full of cigs and tobacco from the reservation here back to Vancouver every other...
If there isn't a mill photo in the future I'm gonna be disappointed.
Mill is on my list this year. But I'll need to pull the trigger in the next few weeks to ensure delivery before end of season. Not sure I'd use it this year or even down the trees I'd mill due to other projects, but at...